2. amps-preamps
  3. 1042614426

Cheap Bryston active or Creek OBH12 passive?

My first audiophile-grade system is in need only of a preamp:

Joseph Audio RM22si signature speakers
Music Hall CD 25 CD player
McIntosh MC2105 amp
Kimber 4TC biwire speaker cables and Signal Cable 2 interconnects

So far for preamps, I've tried using my Denon home theater receiver as well as no preamp (going straight into the McIntosh amp and dialing down the gain controls). Using no preamp wins for clarity and musicality over the Denon for sure (the Denon adds a murky layer over the music), and it seems to be a good match going CD straight to amp (Mac has a very high 220k input impedance). But it's not practical to keep switching cables, so I need a pre. I want to get something cheap for now, around $200 used. I listen to all types of music, from rock to vocals to classical, but more rock than anything else.

And now the simple question: In this system, what do you think would sound better, a Creek OBH12 passive, or a Bryston .4B, .5B, etc? If the Creek wins in your opinion, I'm curious to know roughly how much you think I would need to spend on an active pre before it would start sounding better than the passive. I'm only considering solid state right now, don't want to worry about replacing tubes just yet.

Thanks,
Matt.
matt8268
newbee
4,093 posts
 
I agree w/ Marakanetz in principle, but you must be sure that your source has high enuf output and your amp has high gain. If your source output is over 2v and your amps sensitivity is less than 1v, and you use short cables, you should have no problems at all using the OBH12, and you would have to pay some big bucks to get a SS preamp that neutral.
marakanetz's avatar
marakanetz
5,473 posts
 
newbee,
even if the conditions that you've listed do not have such ideal situation i.e. output under 2v or slightly larger than input sencitivity of the amplifier or cables are 1.5m instead of 1 it still does make a sence to get passive COMPARED to nearly any Bryston preamp.
the problem of wire length can be eliminated if you'll get transformer based passive preamp www.bentaudio.com.
matt8268 OP
92 posts
 
Okay, a bit more info on my system:
Mac amp has input sensitivity of .5V, does anyone know output voltage of the Music Hall CD 25? I can't find it.

Signal Cable's Analog 2 interconnects are 10 ft between CD and pre and 2 ft between pre and power. But these cables have only 17.3 PF/FT of capacitance, so even at 10 ft that's only 173 PF (that's still an acceptibly low capacitance, yes?). If people think I would get much better sound by shortening the 10 ft cable, I could try shorter cables (would have to move things around).
muralman1
1,527 posts
 
Good set up so far. By all means DO NOT use a cheap Bryston. I know you can get them in your price range, but if you stick to that ceiling, you will need to try passive. I use a pre amp that offers both active and passive. I normally use the passive mode as do friends of mine. I know one who goes directly from Wadia to a 100 watt Coda amp with great results. I'm not familiar with all your gear, but it appears to me a passive will work.
newbee
4,093 posts
 
matt, you're in great shape on your amp sensitivity and pre to amp cables. I don't think the length of the cable between the CDP and the preamp will be a problem. The only question is whether or not your CDP can drive the Mac. With the Mac's gain at .5v my guess is that this would not be a problem. And once again i agree with Marakanez re a small loss due to the CDP output would be preferable to a cheap SS preamp (of any manufacture).
More to discover