Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
This Lightspeed sounded open, relaxed and showed me all  musical info that I have been missing for a long time, a real game changer..AN Dac 3 fed by msb digital cd rom drive into lightspeed then the CAT JL2...endless power and dynamics and i have not even matched the
impedance between devices yet...
soundwise
endless power and dynamics and i have not even matched the
impedance between devices yet...
Hi Michael, looked at your source and amp impedance's, and you have a nice impedance match.

BTW: what speakers are you using, as the rest of your system looks very nice, though I'd hate to have to fork out for 12 x 6550's when time comes around.
The ones I used to love were the military NOS G.E. green label ones, who's glass seemed twice as thick as anything else, and they cost over $200 each if you can find them new in box in Australia.   

Cheers George
Verity Sarastro 2 ..they took the Raven Ribbon tweeter apart and added better magnetic parts and also shortened the ribbon surface to widen the dispersion pattern. These speakers with the cat amp are very nice together..best for acoustic instruments.
Hi soundwise (Michael) you asked in a pm,
What about he CAT output impedance any way to adjust that?
MS

Your Verity’s are an easy load for your Cat most of the time, but at 5khz there is a hard load of 4ohms in conjuction with around 50 degrees of negative phase angle. http://www.sonicflare.com/IMG_1966.jpg
http://www.stereophile.com/content/verity-audio-sarastro-ii-loudspeaker-measurements#Xb47wFP2V0w59G7...
But your Cat should be fine still at this frequency as well. As the Cat has only one speaker tap (no way to adjust the output impedance), but having a bit of negative feedback brings the output impedance low enough to handle this, and also there’s not much power needed at this frequency either.

Quote: Cat JL2
http://www.soundbysinger.com/UserFiles/image/JL2%20Sig%20resize.jpg
Circuitry
*Ultra-wide open loop in-circuit bandwidth of the output transformers enables operation of the amps closed loop response entirely within the open loop response, eliminating any requirement for the output stage to perform beyond its natural capability.
***Unprecedented stability into complex speaker loads.
I can see why your liking the sound of the Lightspeed in this very nice system you’ve put together.

Remember the mil spec GE6550’s with the green label I mentioned a few posts back, they are a "cracker" of a tube.


Cheers George
George,

wondering if you have tried to upgrade the parts, if it is possible, and if so, can the sound get even better than it already is!? Noticed that the stage is wider, and that you can hear outer edges if that makes any sense. Also, does dual volume control do anything? I have tried your preamp with same type of audio note dac with Vac music block 160s…also with def tech bp 7002 speakers…not as good as the other setup , but not bad..I will use 1 ohm resisters to tame the tweeter output , but these speakers are 800 used and they sound holographic like the MBL radialstraters which cost as much as a large benz….   imho, bipolar is a far superior design compared to regular speakers..
best,

I am looking forward to your next project!

Soundwise