2. analog
  3. 1035828478

Need help - Set up Helikon using test LP

Over the weekend, I was setting up my Helikon on a Vpi JMW 10.5 arm using the Hifi News test LP and I ran into some problems. The table was a Vpi Aries.

There are four tracks (6 to 9) on the test LP to help setting up the anti-skate. They are 300Hz pure tones. Each track is a few db louder than the one before.

I played the lowest level track (track 6) and it was fine. The 300Hz tone was beautifully reproduced on both channels with equal loudness.

I than played the next louder track (track 7). The right channel immediately buzzed, indicating the need for anti-skate adjustments. I tried twisting the arm leads both clockwise and counterclockwise, one turn at a time, up to 3 turns; but the right channel buzz still persisted.

I also played the track 8, which is a few db louder than track 7. This time the right channel buzzed loudly for a couple of seconds and it jumped track.

The Aries has been perfectly leveled. I checked it with a bubble level and a 10” carpenter level.

The tracking force was set at between 1.75g and 1.80g; it is difficult to be exact due to the limited resolution of the Shure gauge. But in any case, it is at the maximum recommended value so I doubt that was the cause.

The arm was running dry, no damping oil added.

Has anyone tried this? Any help/comments will be greatly appreciated.
sidssp
Ag insider logo xs@2x
kennyb
117 posts
 
I just tested my Helikon using the HiFi News LP. I have a JMW-10 arm that has a 10.5 arm tube and bearing.

My results were similar -- except I also got buzzing on track 6.

Regardless, the cartridge sounds incredible. I have had mine for about two months.
rwd
695 posts
 
Hummmmmm.....does this mean that I have to do the same??? I guess I'll get the Hi-Fi record and do the same and report back....I have the Helikon/10.5.Aries also.
jackcob
36 posts
 
I really don't know much about these things but it sounds to me that this might be more an issue with the tracking capabilities of the cartridge than the absence of a traditional anti-skating mechanism on the JMW. My Van Den Hul Black Beauty, which has a reputation as a good tracker, doesn't begin to buzz until track 9, the last track. (I have a JMW 12.5) Does the Helikon track the Hifi test record better in other arms? How much so?
sidssp OP
1,077 posts
 
Ok. I got in touch with Mike at Vpi. He told me to set the tracking force at 1.9 g for the Helikon, the manufacturer recommended maximum of 1.75g is not enough.

My arm wire may have too much glue on it and I need to loosen it up using a hair dryer. Right now if I twist the arm wire more than one full turn counterclockwise, it forms an "S" shape. It should form a smooth arc in order to function properly as a spring.

Mike also told me a procedure that involves using a dime to setup the anti-skate.

I am going to try all these tonight and will report back what I found.
twl
3,251 posts
 
Jackcob, the 12.5 has more mass and superior geometry over the 10.5, so it should be a better tracker. The reason that these Helikon owners are having problems, is that the Helikon is really too stiff in the compliance department for these unipivot arms. I try to tell people this, but nobody listens. It is a marginal match up, and that is why the tracking force needs increasing, and it buzzes on track 6 or 7. The JMW is a good arm, but it needs a medium to high compliance cartridge, not a medium to low compliance one. I have said time and again on these pages that unipivots are not good matches with low compliance, and I stand by that statement.
More to discover