Eminent Technology ET-2 Tonearm Owners

I thought this would be of interest regarding power hits and LP playing.

We have been enduring the hottest summer I can remember. There have been a few power hits due to demand and storms.

We had a power hit on a beautiful but very hot day this past Saturday. I happened to be playing LP's.

I always knew I had some time with the air bearing tonearm due to the pump design but never tested or actually experienced it going out before.

The Timeter pump lets out PSI gradually. Like a balloon letting its air out slowly. I have about 12 seconds to lift the arm before it reaches a low enough PSI to actually start skipping (just under 2-3 psi).

The Verdier will continue to spin for about 25 seconds when the motor is shut off. The JN Lenco spins for just under 20 seconds. The SP10 MKII is dead on power out :^(



Cheers

Dear Frogman, Your 'complaint' remind me of this story.
A satisfied client to his lawyer:'dear sir I have no idea how to thank you.'
The lawyer: 'dear sir since humans invented money this no
problem at all.' Not sure why but all my acquaintaces enjoy
in partucular to tell ME such lawyer tales.
Well I expressed my indebtedness to you already but I had no idea that you are also a lawyer. As such you should know that an demand or claim needs at least some legal foundation. Otherwise I would be able to demand from Chris
to lend me his beloved ET2 for a month or two.

Regards,

Otherwise I would be able to demand from Chris to lend me his beloved ET2 for a month or two.

Nikola – Be careful what you wish for. You are a very witty and brilliant minded person. I get that just from reading your posts here and emails. I am no match for you. Now if you read my OP you will see that I am on my 10th year now with this tonearm and I am “still figuring it out”. So what makes you think you can figure it all out in 2 months ? That’s pretty bold I must say.

Now understand “figuring it out” to me means making it as best as possible. Oh sure just setting it up and getting it working is no problem and even on a boring old aquarium pump. I even have one that you can barely hear that can even stay in the same room next to it with a filter for moisture. But there is so much that can be done here to optimize sonics and customize it. Imagine being able to change your wiring out in 10 minutes for copper, silver, whatever, tuning the arm for different cartridge compliances. magnetic damping, etc….

I take the important clues from our friend Geoch, that when buying an audio product look for those that give you access to the critical areas that can be improved. Those are the genius designs. BTW Geoch put out a couple of really good posts recently here (I thought) on how to optimize a pivot arm and very few on the thread seemed to show any interest :^( yet….

http://forum.audiogon.com/cgi-bin/fr.pl?eanlg&1309722499&&&/Graham-Phantom-II-12-quot;-dimensions-an

Here’s my deal for you only as I recognize these arms were not common there. JC Verdier as I said had no clue what tonearm I was using on his table. I will send you my second ET2 tonearm – the 2.0 HP Version to use for a couple of months. If you commit to two things.

1) Read the manual. If you can get through the manual you will know you are a candidate for this tonearm.

2) Commit to getting a proper air supply system that will give her the air quality she needs to run a good race.

The Olympics are on TV. I run everyday so the running events I am more interested in.
BTW tell me this is not cool. Just for today however, Google's Aug 7th homepage.

http://www.google.com

The ET2 tonearm is like a long distance runner. The tonearm itself is the body and lungs. The Pump is the heart with the tubing being the veins. Success and optimization with this tonearm for me has been 40 % proper setup and 60 % air delivery system. Improve the condition of the heart (pump) and just like the runner the ET2 improves.

BTW - There are some out there that have custom 50 PSI ET2 models. The problem as I see it is that Bruce is a really low profile guy. He is the type of guy that never felt the need to put words like “Supreme” on his tonearms. In fact unless you measure the spindle or are familiar with the tonearm to notice the larger spindle, you will not know which model you have. Those with 50 PSI models if they sold them, the new owners probably don’t know what they have.
Have you seen his subwoofer Nikola. Did you realize that Bruce made the first true subwoofer.

http://www.rotarywoofer.com/

Ok so the offer is out with everyone here as a witness. The manual can be found here Nikola in two parts.
Again be careful what you wish for.

http://www.eminent-tech.com/main.html

Ready, set , go …

Just a fan, and this tonearm is just a tool in an overall system.

Dear Chris, Your willingness to lend me your ET2 is moving
but you ruined my argument 'against' Frogman. The reight response should be : nobody has the right to DEMAND anything without ,uh, some legal fundation. We are talking
about lawyers not about tonearms. However your kindness is
also suspect with all those warnings regarding the pressuposed knowledge and experience . I feel as if I need to get a degree in mechanical engineering first before I can handle the complexity and the sensitivity of the ET2.
But, you know, I was familiar with the linear tonearms befor you was probable born. In the 70is I got my first Rabco. But, as is usually the case, after some time
we want 'better than the best' so after about 3 years I got the Goldmund. For this one I wish you were there with
your warning: 'Be careful what you wish for!'. Your 'brilliant' co-member got the inferiority complex from this monster. The first time in my HIFI life that an
component made me cry and certainly not from joy. Then I
promissed to my self never ever to mess with linear arms. As a kind of 'sweet revenge' I now own 7 pivoted tonearms.

Regards,

Cheers Nikola

Your willingness to lend me your ET2 is moving but you ruined my argument 'against' Frogman. The reight response should be : nobody has the right to DEMAND anything without ,uh, some legal fundation.

I realize that as you are a lawyer, you develop a script of dialogue (like a play), and if things go according to plan you run through the script as expected with a good result. But I have a confession to make. I am pretty good at ruining arguments as I have spent 25 years doing project management. I am a PmP. That’s not short for PIMP. I wish it was. That way I could make everyone happy. PM’ing does not follow logic all the time because the clients are not always logical, like the justice system. Now the business I am in also concentrates on preparing clients for a worst case scenario. So over the years these processes have become ingrained in me. My views definitely represent extreme ones as far as been careful and preplanning for sure. My family have made me aware of this a few times.

No you don’t need to be a mechanical engineer with the ET2. This is really no different than bringing in any new appliance into the house "that actually works". All the instructions are the same for all of them. After you unpack, the manuals always start with similar language.

"Read the installation and operating instructions first."

Lets be honest here - how many actually do that ?

Therein lies the problem.

Offer stands open just for you – I will let Frogman and yourself get back to the lawyer stuff now.