Anti skate and tonearm damping query


I have read a number of threads relating to both antiskating and tonearm damping on the JMW 9" Sig.arm and find myself a bit confused.......I have been experimenting a little and have reached the conclusion that I must be deaf. I have not used the additional antiskating system, I have tried twisting and not twisting the leno wire and can hear no difference. If the Leno wire is not twisted therefore no antiskate, will this damage the stylus or the album??
I have also filled the damping well above the taper to the base of the point and still cannot hear 'the music being sucked out' or indeed, an improvement. Do I fill the well up to the point!! and then work backwards. Those that finetune using the damping seem to have some sort of epiphany when the 'sweet' spot is reached.

Can someone please shed light on how I should be going about setting the AS and finetuning the damping on the arm. The table is a scoutmaster with super platter and sds, the cartridge is the dynavector Te Kaitora Rua

Thanks
wes4390
Hi,
The lemo connector has a small amount of anti-skate bias, even when not twisted. Twisting it (counter-clockwise, I think?) will increase the anti-skate force.
I experimented with the anti-skate on this arm, both via the lemo connector and the anti-skate assembly. The difference I heard was minimal. I only heard a noticeable difference when way too much anti-skate was applied. The soundstage moved off-center and the sound became smeared.
I currently use the optional anti-skate with no weights on it. It makes no difference that I've ever been able to hear consistently, but it tracks the test record better and so I would assume it's probably better in terms of groove wear.
The great improvements I've made with this arm were the result of a) dialing in VTF/VTA, and b) nailing the alignment with a Mint LP protractor.
I've never tried using the damping fluid. Just seems too messy.
Regarding Srwooten's post, if you don't have a syringe handy, a Q-tip works too.
Cheers.

Tom
Skating force is a 'twisting torque'. It occurs only in tonearms that have an angular offset built into them to help minimize tracking error - making it zero at two points across the record instead of one point (which would result if there were no offset.) The amount of the skating force is the result of the friction force (or drag) of the stylus in the groove times a lever arm. The length of this lever arm is the length of a line drawn from the stylus, pependicular to the axis of the cartridge, to the point where it intersects at 90 degrees with a line drawn through the pivot of the tonearm. Since this relationship remains constant, regardless of the stylus' position on the record, the skating force remains essentially constant across the record. I say 'essentially' because there is some very minor variation in the force-of-friction as the velocity of the stylus-in-the-groove slows down toward the center of the record. ANTI skating force, when applied with a spring, can be made to compensate for this (VERY slight) variation, as in SME arms. However, the weight-on-a string method or the twisted-cartridge-leads method will work just fine. Whether AS has an effect (or not) depends on the design of the cartridge. Stiffer suspension material and/or lower VTF reduce the need for AS. Further, the larger the size and strength of the magnetic field in which the coil is immersed, the less AS will make a difference/improvement.

Increasing the VTF will ALWAYS increase the skating force/torque because increasing the VTF increases the friction of the stylus in the groove. The fact that line contact styli produce so much less friction (compared to conical and elliptcal styli) is why moving coil cartridge makers (using line-contact styli) are able to use higher VTF's and stiffer suspensions necessary for the generally superior performance of MC cartridges.

With MM cartridges the situation is reversed. True they customarily track at 1/2 the VTF of MC cartidges, and many of them now employ line contact styli. However, because of their extremely compliant suspensions, it's easy for just a little skating force/torque to pull their tiny magnets out of alignment with the field coils.
.
Thanks again for all of the comments.......much appreciated.

Tom,
When you set the vta was it done by sight i.e. with the lined card as suggested by vpi, or by ear after this and If you turn the vta wheel clockwise does this lower the arm? I am currently on my second Mint...the first one cracked as I was taking it off the platter spindle.
Skating force is a result of the offset of the polished area of the stylus in perspective of the groove wall. During the journey of the tonearm cross the record side this offset becomes zero 2 times - the zero tracking error point - and is depending on the tangential error angle (which changes all the time - becoming more and less again during the journey from and towards a zero error point).
Less derivation from tangential zero error = less skating force.
Skating force too is influenced by misalignment of the stylus in the groove and - to a VERY high degree - by the total contact area. Larger contact area (= modern line contact) is far less force on the groove wall with a given VTF as the skating is a by-result of VTF divided through contact area.

In summary:
- less derivation - offset - from tangential zero = less skating force.
- super precise vertical alignment of stylus in groove = lower skating force.
- larger contact area of stylus = lower skating force.
- old - conical or elliptical - stylus = higher skating force compared to line contact or similar.

MOST IMPORTANT: skating is NOT linear, but a force which gets higher, lower, zero and higher again.
Trying to compensate such a force with a linear anti-force is......... well....... no good idea.
"Correctly applied" anti-skating would fix the problem in 2 short moments of the record side and produce a new problem for most (98%...) of the rest.

Then there still is the (objective and empirical by observation ...) "fact" that most tonearm/cartridge- combo featuring very high VTF (2.5 grams +) do indeed produce LESS skating force .........

Thats why Ortofon did not care for antiskating at all in its 12" tonearms w/SPU cartridges and why my FR-66s runs smoothly w/ FR-7fspec. without any anti-skating.......
God bless America. Dertonarm has a right to express whatever ideas he feels are true ;-) and on any subject. Besides, they say laughter is the best medicine. So I say 'Good luck' to him!