Dunlavy SC IVA X-over resistor values


I own Dunlavy SC IVAs. Does anyone know the values for the resistors in the crossovers? I wish to upgrade the resistors to better quality. Thank you very much. Jonathan
jonathanhorwich
Thank you all for your continued input. My unsubstantiated premise regarding some of the parts in the SC IVAs is that Dunlavy did not have the time to hand match each component in each speaker. Nor did he want to jack the price of the speaker way up with the absolute best parts. Whatever, some of the parts can be improved judiciously. On the other hand, Dunlavy hit the jackpot with this speaker as something about it is so right and so coherent. The bass quality is as good as I've ever heard from a cone speaker. So messing with it is a careful process. Here is what I have found so far that improved the speaker all based on input from Audiogon members (since I had no clue about these matters--I can just hear the smallest changes in my system). 1. I put cardboard on top of the speakers. I bought thick cardboard flat boxes at UPS store for 5.00. I cut it up so one flat piece about four feet long was used for each speaker. I then folded the cardboard so it sat on the speaker kind of like those small picture frames do with the picture leaning back and a support behind it leaning on the table it is sitting on. In this case it sits on the speaker slanted back away from the front. Hope this is clear. The theory from Tom is that it helps equalize the distance that each woofer is from a surface, the bottom woofer being closer to the floor than the upper woofer. Did it work. Yes. This is a minor but worthwhile upgrade which makes the images a bit more stable and present. I took them off and on to check this. If I keep these there I'll cover them with speaker cloth so they look a bit more coordinated. Right now they are ugly as sin. 2. I replaced the tweeter and midrange screws with brass. This made the highs less tizzy and more solid. 3. I had the speaker elements themselves soldered instead of using the cheap push-on connection tabs that exist on each speaker element. That really improved the quality, smoother. 4. I installed a direct electrical line from my elect service box right to the wall that my amp and pre-amp plug in. I had VH Audio tell me what to get. I put in new outlets (Oyaide receptacles and #10 wire.) Major change for the better with solid images, less noise, etc. By the time all of these improvements were done my speakers sounded about 10-15% better. A major improvement for speakers that were already wonderful. Those are the improvements. Next I'll post what didn't work and in fact ruined my sound temporarily. And ask for data from those who have made the resistor change to the SC IVAs. I cannot imagine it not making a major difference. Jonathan
Here is what I did to my SC IVAs that didn't work, from subtle to bad. 1. I put short cones under my SC IVA bases. It made almost no difference. If forced to decide, I'd leave them there but either way I don't hear a big or even small difference. I think the bass is slightly tighter with the feet. They are some generic cone and not high quality. As a note I have a very thick solid concrete floor with an indoor outdoor carpet over it. Basement studio. 2. Two Audiogon members said to remove the bases of the SC IVAs and it would make a noticeable improvement. I did this and the magic I had gained from my other improvements completely disappeared. This was not subtle. My system was worse by about 10%. I have no idea why but it was bad. I put the bases back on and voila. The great presence I had achieved was back. Without the basses the sound was recessed with loss of solidity and presence. Frankly this makes no sense to me why this would be so much worse, but it was. These are the only changes I made that either made little difference or were worse. Jonathan
Dear All Who Helped me,

As a final note I chickened out on any other changes to my SC IVAs after taking the bases off made such a negative change. My system sounds great since re-attaching the bases so I'll leave it at that. If anyone finds any other changes that really help I hope they will post it for our mutual benefit. But for now no more major changes for me. Thanks again. Jonathan
DAL's have narrow dispersion. You need to pay precise attention to exactly where you position your head when listening and making A/B comparisons. A few inches may change what you hear when listening critically. Typically it is recommended to place them far apart and toed in - this means if you lean forward then the sound may change considerably too.
Respectfully to Shadorne, if DALs have a narrow dispersion then why is distance and angle from the sidewalls so critical, as well as the reflectivity of these walls?

My experience with DAL and Duntech speakers suggests two conditions. The speakers are of such quality that listening outside the "sweet spot" can still be very pleasurable. But I will admit that to optimize critical listening, where you sit will be important. And this relates to vertical position of your ears as well as horizontal position. This is because of the D'Apolito array of drivers -- think of them as a stereo pair turned 90 degrees and it should be obvious why placing your ears at tweeter level is important.

Back to Jonathan, for your DALs I would do everything that is practical for placement and room treatments before worrying about future tweaks to the speakers themselves. Just as with any quality speaker system, you should start with the environment where they are ask to perform.