Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57

Hi Shakydeal, Sonic Euphoria looks to be out of business.

I can understand why you like LDR passives, this is the problem with TVC/AVC passives, look at the frequency response of it into 100kohm 10kohm 5kohm input impedance of poweramps. It rings like a bell starting at 10khz!

Only into a 1kohm input impedance poweramp does it behave itself, but 1kohm is a severe impedance mismatch, and then it rolls off to early in the HF.

http://www.stereophile.com/content/sonic-euphoria-plc-passive-line-stage-measurements

The Lightspeed Attenuator itself with low capacitance interconnects is flat from 0hz(DC) to mega hertz.

Cheers George
Grorge,
What do you mean by "rings like a bell starting at 10khz!"? An example would help.


The rising peak into the high frequencies in the first graph I last posted.
If this was to be seen as a square 10khz wave response on a scope, the top of the square wave would be ringing similar to this 1st link, instead of being perfectly square 2nd link.

http://www.digitalprosound.com/2001/03_mar/images/testing/fig8_650.gif

http://imagizer.imageshack.us/a/img14/1007/2u3a.jpg

Cheers George
Hwv1 hi.
Thank you very much for your praise and very in depth review. And I'm not surprised it better your TVC preamp, as Shakeydeal also has said, as transformer (TVC/AVC) preamps have a problem as I've outlined to Milpai above.

Yes with any passive preamp or active tube preamp with their high'ish output impedance, when you try to simultaneously drive your main poweramp and a subwoofer amp/s, you create a heavier load for the preamp to see. And it's really only suited for solid state active preamps with their low output impedance to drive.

This problem is the same for any passive or tube preamp, and the way around it is to use a high input impedance buffer in front of the sub amp as you've done, as most sub amp have stupid low input impedance.

Cheers George