2. analog
  3. 1233265575

Turntable Speed

I own a Transrotor "Atlante" turntable. I purchased it about 2 years ago with all the available upgrades (platter and tonearm). This unit was $4500.00 without cartridge. It is a belt driven product with an outboard power supply which lowers the incoming voltage to the 18 volts the motor requires. My problem is turntable speed. My 'table speed is about 34 rpms. I could be more accurate if I had better measuring equipment. Anyway, that's about 2% over the correct speed and you can definitely tell the difference in sound quality between 34 and 33 1/3 rpm!. I was a little upset with this revelation and called my dealer about it. I also talked with the dealer's supplier. I received several reasons from these people as to why the speed was not accurate among which was that my power was "out of tolerance." But when all was said and done, none of the given reasons held water and I am now being advised that really there is nothing that can be done. That there is no defect in the equipment and if the speed problem continues to bother me, I should invest $1700.00 in a Transrotor speed controller. As I think over this, I wonder why platter speed is never mentioned or measured and reported on in the reviews for turntables in the major audio mags. (This could be because there isn't any problem, except for my 'table, or there is and no one is admitting it). To my way of thinking, platter speed has to be one of the primary functions of a turntable and that manufacturers would be making sure that their products' platter speeds were within strict specifications. At least better than 2% margin of error as is the case with my turntable.

My question is: Is platter speed error a given in this industry or is my 'table actually in need of repair? And, if platter speed is an industry problem, why are we as consumers paying thousands for equipment which actually doesn't work up to expectations?

frepec
sonofjim
557 posts
 
I also don't see how any turntable could be accurate without a speed controller. I check my speed every day and often have to make minor adjustments with the SDS to get right on 33 1/3. I'm sure a multitude of factors work together to change speed slightly from day to day. Keeping it accurate is an ongoing process.
palasr
453 posts
 
"Keeping it accurate is an ongoing process. "

There are, however, several steps that can be taken to ameliorate having to tinker continuously. Make sure the belt and belt path are scrupulously clean; be certain the table's bearing is clean and properly lubricated; be certain the table is level (this is a must); try to maintain a constant ambient temperature in your listening space - believe it or not, the viscosity of both the bearing and motor lubrication change considerably over a relatively small temperature range. I'm sure there are others I am neglecting.... Good listening,

-Richard
johnbrown
195 posts
 
AC synchronous motors are dependent on the line frequency for correct speed (such as the aforementioned Scout) so I imagine that VPI offering the SDS as an aftermarket accessory (though in reality it's a necessity, since frequency can vary, thus changing the motor speed) is simply a marketing decision to keep initial tt pricing down.

A DC motor, though, should be able to run at the exact speed required every time it's turned on-so with the correct pulley and platter size, and belt thickness, 33 1/3 rpm should be easily maintained, minus the effects of wear, dirt, belt slippage, etc.

Which leads to the possibility that some manufacturers purposely build their tt's to run slightly fast, in order to give a false sense of excitement, and PRaT, to the sound.

This is just a guess-AFAIK, no proof exists-though Rega has long been rumored to employ this technique.
dan_ed
2,451 posts
 
A DC motor, though, should be able to run at the exact speed required every time it's turned on-so with the correct pulley and platter size, and belt thickness, 33 1/3 rpm should be easily maintained, minus the effects of wear, dirt, belt slippage, etc.

If that were the case we'd all be using DC motors and none of us would be concerned with speed. ;-) Unfortunately, it doesn't seem to work that way.
frepec OP
17 posts
 
I'm beginning to get the idea, now. I did some checking and it does seem to be that most high end turntable manufacturers also have speed controllers as part of their product line. I think that johnbrown has it right. AC motors are not reliably accurate and thus require speed controllers to get them dialed in. It does seem like a marketing ploy. Let the buyer discover he has a speed problem and then sell him a speed controller. It's beginning to become evident to me that speed problems are the nature of the business and that there is most likely nothing wrong with my equipment. I just think that with all the technological advances that have been made in the home audio field, that making an accurate platter drive motor should not be that big a deal. Not being an electrical engineer, I could be way off base with that statement.
More to discover