Walker Audio Prelude LP Cleaning Solution


I did not want to post this as a full review as this is my initial first impression using the newly released Walker Audio Prelude LP Cleaning Solutions.

Prelude is a 3-step process consisting of enzymes, premixed cleaning solution and an ultra pure water rinse (made via a 7 stage filtration process). I comes nicely packaged with the following: a 64 ounce container of ultra pure water, a 16 ounce squeeze bottle of premixed cleaning solution, a second bottle of water in a 16 ounce squeeze bottle, an empty 4 ounce squeeze bottle, and a jar of enzyme powder, along with a small scoop and a slightly larger scoop.

Lloyd’s research indicates that enzymes in a solution only have a life cycle of 8-10 hours before they die off. By keeping the enzymes in a powder form, and only mixing enough to be used during a cleaning session ensures they stay active.

If you plan on cleaning 5-6 or so LP sides at a time (which is what I have been doing), use the small scoop in the enzyme powder. Place the powder in the empty 4-ounce bottle. Add some of the water from the 16-ounce container up to the “A” mark on the 4-ounce bottle and shake to mix. Apply to the pads of a cleaning brush and lightly scrub the LP as it spins on your RCM. Let it sit for 15-30 seconds and vacuum off.

Using a second brush, apply the premixed cleaning solution to the pad and apply to the LP as above. Let sit for a few seconds and vacuum off. Do not let either solution dry on the LP.

Using a third brush, use the ultra pure water as a final rinse and vacuum off.

I have had lots of experience with different LP cleaning products, including Disc Doctor, Audio Intelligent, and L’Art du Son. The AI solutions are similar to Prelude in that they also use the enzyme solution as a pre-treat prior to cleaning. The AI enzyme come premixed, unlike the Prelude. The enzyme powder formula of Prelude ensures that the enzymes stay viable until they are needed. I really like the AI solutions when I used them, and missed them when Paul sold the business.

That said, The Walker Audio Prelude is the best of the AI, kicked up several notches. Lloyd Walker has hit another one out of the ballpark. After cleaning several LPs that I thought I knew backward and forward, I can report the following: surfaces are dead silent, with no residue what so ever from any of the three steps. There is no static build up, and even well played LPs have that shiny right out of the sleeve look to them.

Focus, detail and transparency are the first three words that come to mind when describing what I am hearing. The inner detail on familiar LPs lets me hear for the first time things that have been there but never fleshed out of the grooves the way it is after using Prelude. At least, that's what MY ears are telling me. The music just leaps out from the utter blackness of the grooves. And, your records are REALLY clean. What else could you expect from one of the true masters of the analog arts? Who better to bring such a great product to the market for LP lovers than the man who builds what I consider to be the finest LP playback product in the world?

Give Lloyd a call and talk to him yourself about Walker Audio Prelude. I have no financial connection to Walker Audio other than the fact that I am a very happy customer and use many of their products in my system.

Kudos to Lloyd, Felicia, and Fred for creating another great Walker Audio product.
slipknot1
I too have tried Lloyds new record cleaning solution and it is all that you claim in terms of the sonic improvements it produces. My only reason for not using it each time I listen to LP's is the limited half life of the enzyme solution [I don't want to mix up more than I can use at one time and then have to throw the unused portion out. But I will swear by the sonic improvements, you really havent heard all that is on your LP's till you clean with this stuff!!!
Perditty, Lloyd tells me that you need to use the enzyme step only *once*. After that first cleaning, if there's ever a need to clean the LP again, just use the cleaning solution and rinse.
Slipknot1,

Joe,

The response to your thread must be a record, or close to it, 14 responses in 2 days, congrats.

From previous posts,------- "Enzymes are catalysts - a very special kind of organically grown catalyst with a very precise chemical definition. A "true" catalyst in chemical terms substantially reduces the energy barrier which exists between atoms and which prevents the atoms from "getting close" enough to react and form a bond with one another. An enzyme, like all strictly-defined catalysts, is therefore said to lower the energy of activation of a reaction; but, the catalyst is not changed in any way in the process - kind-of like a conduit - a path through which reactions occur."

It appears from the above that the key is the enzyme solution, as a pre-treatment, allows the cleaning solution to work better as there is less energy required due to the catalyst effect created by the bonding of the enzyme solution and the cleaning solution.

Just a thought; a catalyst, by definition, affects the speed of a chemical reaction without actually taking part in it. Time and heat are both catalysts. Enzymes also contribute to the effectiveness of the cleaning process , the frame of reference that we are referring to in this text. We should be able to add another catalyst to enhance the final result. I suggest a vigorous mechanical action , much more violent than brushing.

Ultrasonic action should only enhance the final result.

Your thoghts.

Ken

Thanks, Slipknot.

Can you describe the process that goes on with the premixed solution? One ounce (you indicated that you actually used less) of cleaning solution for 20 LP sides equals about 1/3 teaspoon of solution per side. Do you feel that that is enough fluid to "flood" the surface and bring the crud from deep within the grooves to the surface while you scrub? It seems like a healthy amount of this quantity will be soaked up by the brush.

When I imagine cleaning an LP I imagine the dirt being put into suspension on a very wet surface before it is vacuumed off. Can this be effectively done with less than 1/3 teaspoon of solution?
Here are a couple of reasons that enzymes could become inactive in solution. Most of this depends on the concept that an enzyme is a large polypeptide chain with a tertiary structure that is relatively unstable compared to simple chemical catalysts. Changes in this structure can lead to its inactivation.:

1. Denaturation of the enzymes by agitation at air:water interfaces. Do you see soap-like bubbles when you shake the enzyme solution? Uh oh, that is enzyme that has lost its tertiary structure by denaturation caused by separation of hydrophilic and hydrophobic regions of the polypeptide chains at the air:water interface. Better be careful mixing this solution and use swirling, rather than shaking motions. Hint: roll it between your palms.

2. Degradation due to proteases. The world (inc. probably record surfaces) is full of proteases made by microbes and even your fingers and these can attack enzymes and inactivage them by cleaving the polypeptide chain into smaller pieces and amino acids.

3. Inactivation due to inhibition. Enzymes often require cofactors to work and depletion of these can inhibit further enzyme action. Alternatively, inhibitor molecules can bind to the enzyme and modify it to an inactive state.

Hope this helps clarify things. (I am a molecular biologist with a background in protein x-ray crystallography and the design of peptide detergents.)