What to listen for when setting VTF?


I've read that folks fine tune VTF by ear, so was curious what you listen for. How does more or less VTF affect sound? Thanks.
gbb
...for some classical recordings, the strings have some silbius or distortion, that are corrected by going to 4.0. I am still running it at around 2.2, but was curious why it is that way
There are several possible causes, including various setup parameters and phono stage slewing distortion, but here's one cause I'm certain is involved to some degree in your system.

Every stylus has a contact radius, which determines the minimum size of the groove modulations it can trace. When a stylus encounters modulations smaller than it is, all it can do is scoot past the tops, playing part but not all of the waveform at that frequency. This necessarily results in clipping of the waveforms at these higher frequencies and perhaps in the momentary loss and regaining of stylus-groovewall contact, all of which we hear as "sibilance". The larger the stylus, the lower the frequency where this will begin to occur.

The contact radius of the 103's conical stylus is much larger than the contact radius of styli in some more modern cartridges. Finer stylus profiles trace smaller modulations (ie, higher frequencies) cleanly, and do not start "scooting" past small groove modulations until higher frequencies.

Increasing your VTF to excessive levels will not make the stylus fit into modulations smaller than it is, but it may mitigate the resulting distortions in a couple of ways:

1. Increased pressure between stylus and LP assures that the stylus will not lose contact, which makes the (unavoidable) clipping of too-small modulations as smooth as possible.

2. Increased pressure between cantilever and suspension is smothering higher frequencies, much as soft earplugs block higher frequencies while letting lower ones through. In effect, you're using excessive VTF as a HF rolloff filter.

If you listen to a lot of this kind of music, and the distortion bothers you, I'd suggest that your next cartridge be one with a line contact or micro-ridge stylus. All else being equal, they reproduce HF's more cleanly than conical or elliptical styli.
Dear Toufu: I can't say if the Zu is a good match for the tonearm you own ( ask directly to the manufactirer about ) but if it is then the problem is in other " place ".

The Zu specs " talk " that the recommended VTF is 2.5grs but this manufacturer does not point out a VTF cartridge limit ranges ( up-down ) like almost any other cartridge builder so maybe the Zu can run " safe " up to 3.0grs we don't know about and you have to ask, here too, directly to the manufacturer.

The " right " VTF is not only for the cartridge track fine with out tracking distortion and to protect the LPs from fast wearing but along the suspension design to center the coils to achieve the quality performance design targets.
If your cartridge is out of that " right " VTF then all those factors name it could suffer a " degradation ".

+++++ " but for some classical recordings, the strings have some silbius or distortion.... " +++++

Toufu your cartridge ( like any other one ) is not a perfect one, it is far from there, the ZU performs according its price range or something a little better: nothing more nothing less.
In the other side all the recordings are far from be perfect too so you must accept " distortions " all over the analog music sound reproduction.

Maybe you are " waiting " that your analog rig performs near perfection. Well you can't wait or look for in your today audio system, you have to accept its limits.

Anyway, IMHO it will be worth to contact directly to the Zu manufacturer and explain to them what you are experienced and see which advices and support they can give you, maybe your cartridge is out of specs somewhere.

Regards and enjoy the music.
Raul.
Raul makes another good point. I'm not familiar with the Zu version of the Denon 103, but the normal versions of that cartridge are not an ideal match for lighter weight unipivots like the JMW 9. Compliance, while not actually as low as Denon's quoted 5cu, is still lower than optimal for this tonearm. That can affect tracking.
I added a 5g headshell weight to my VPI and the problem went away... Now I get no distortion at 2.2g for those records. Thanks again for the help.