2. tech-talk
  3. 1065448013

Stacking components?

I have a Sony 7700 and am getting a Jolida 1501. Is it OK to stack the Jolida on top of the Sony? Both will be going in a heavy wire 18"x18"x74" tower/shelve unit. The tower will have good contact with the floor and I was going to put a slab of granite, wood, etc. underneath the Sony as well. Also, I was going to use something like Vibrapods underneath both the Sony and Jolida to help with vibration even more. I've heard/read that a small bag of sand or other weight on top of the CDP will help some. Can I combine this effect by having the Jolida on top of the Sony or will heat be an issue? Any other ideas for cost effective isolation in this type of setup? I realize the wire tower isn't perfect for this but it fits where I want it in my den perfectly and it is well made and solid. Here's a link to it(bottom/middle of the page):
http://www.125west.com/InterMetro_Home_Office_Furniture_Metro_Dorm_Sale_wire_shelving.html

I'll also have a small 5 gallon mini/nano reef on the bottom shelf and a 14" Toshiba television above the components. I'd like to try and get it to work well with the components in there if I can.

Thanks for any input.
asahitoro
asahitoro OP
217 posts
 
Onhwy61,

Thanks for your experienced input. I'm eventually going to buy a dedicated audio rack but for now I'm on a tight budget. An expensive audio rack is something that will have to wait for now. I realize how important things like room acoustics, isolating components/good rack, etc. are so I'm trying to do most of that the DIY route. At some point I'm going to hit a point of diminishing returns cost wise relative to how much improvement I can get out of my modest system. I actually thought that stacking my components may help some in making things more solid/vibration free. I'm going to give it a shot with the wire tower/maple shelves/Vibrapods. I just hope I can train my ears well enough to hear the subtle differences while I experiment to make things more effective.

Thanks again for your input.
suits_me
121 posts
 
Here is what Ken of Neutronics platforms said: "If you're not into DIY, check out the IKEA Corras- Replace the casters with spikes and you've got a fine performing, attractive 3-4 tier rack."

By DIY, he was referring to the IKEA Lack table, on which there are several threads here at gon.
elizabeth
6,726 posts
 
I stack.
Usually I try to leave extra space between by using 'TipToes' or thick rubber bottle stoppers, I also have a few sorbothane hemispheres. But some equipment is very cool even in use, and some of that stuff I have even taken the feet off and just used a thin pad of cork between.
I don't usually stack more than 3 high, and try to stack so the stuff used together is not together in the stack.
I have gone as high as five units in my years of audiomania.
A few items really need a lot of space though... a pre-pre phono stage usually should be pretty far away from other stuff.
Class "A" preamps should be on top, with plenty of circulation of air around and under... Amps should not be in any stack... or even on a shelf below other stuff if they get hot.
asahitoro OP
217 posts
 
Elizabeth and Suits_me,

Thanks for your input. That IKEA stuff looks like it could be a good alternative. I wish I had a local store to see some of it in person. I'm only dealing with two components here so I'm trying to make the most efficient use of space in my den by keeping everything in one rack. Since I haven't got my amp yet, I'm not sure about how much heat I'm dealing with. I think I'm still going to give each component it's own shelf and Vibrapods/etc.. I'm more concerned about vibrations with my CDP than my amp. In my setup, with the modifications that I am suggesting, shouldn't that be enough for the amp? Will it really make that much of a difference sound wise in my modest midfi setup? Should I just opt to put the components on my desk beside my monitor? My desk is more of a table(60"Wx24"D), my monitor is about 22" wide and my speakers will be on stands beside both sides of the desk. Maybe by coupling my desk via spikes, etc. to the floor and stacking my components on there with some Vibrapods will be a better alternative?

Thanks again for all of the input.
shaqspack's avatar
shaqspack
91 posts
 
I have good rack and have seperated AMP and power conditioner. Have wo shevles for assorded CD/DVD/DVDO-HD/Pre-pro/DTV.

With good shelve litle heate issues, I am concerned with elictric effects and such. IDEA and OK and avoid.

Thanks
More to discover