Need MC Step-Up Transformer advice?


I'm thinking of a different approach dealing with my low output Benz MC Cartridge.
What is the feeling and opinion in this forum about Step-Up transformers .vs. active amplification.

Right now I'm using a Audible Illusions M3A (With Gold Phono boards), Levinson Amp and Quads.
I will probably be changing preamps soon - not sure to what.

Anyone have experience with multiple transformers that can guide me towards some and away from others?

Thanks, Steve
rotary914
I second Raul's opinion. I have tried well burned-in S&B TX-103 transformers (also briefly Cotter trannies several years ago) in my VPI/Shelter 501/Counterpoint SA-9 in MM/Acoustat servo OTL power amps/Acoustat model 8's. The S&Bs were configured at 20db gain with either 50 or 100 ohms. My modified Music Reference RM-4 or Audio Research MCP-33 is much more musical, dynamic and involving. This could be a system matching issue. Since my experience is limited with my own system, I cann't generalize the results. It's just my experience with my system.
Dear Joe: The best you can do with your Allaerts is through an active gain stage: you don't have to worry about DC offset. Only if the phonopreamp was or has a faulty stage.

Great cartridge: congratulations !!!!!

Regards and enjoy the music.
Raul.
Here's 30 years of perspective on moving coil step-up transformers vs. active preamplification: Neither approach to scaling up the signal from a low-output moving coil cartridge has conclusively defeated the other. The theoretical shortcomings of transformers are well-known and cited in a post above, but that doesn't mean a transformer might not sound preferable to you. It's true that back in the 70s, when all preamps had mm phono sections, generally transformers were preferable to the solid state pre-preamps of the day. The Levinson JC-1 was the primary transistor contender to take seriously. I'd say the period from about 1975 - 1985 saw transformers rule. This was the era of the excellent Mitch Cotter, Koetsu, Audio Interface, etc. xformers. A Koetsu was $1000 circa 1980 -- real money then.

When CD drove phono stages out of preamps and the market became dominated by linestages, engineering and resources directed into stand-alone phono sections yielded phono preamps that cost more than conventional phono + line preamps of just a few years before. The raw devices and power supply techniques improved to, so we got tighter, quieter tube phone stages, and considerably more musical solid state alternatives. Over the past 30 years, I have gone both ways on this. I've had Cotter, Denon, Ortofon, Koetsu, AI, Quicksilver and EAR step-up transformers. They were all euphonic and had very specific sonic signatures and this crowd did not generally roll off in the frequency extremes in a musically-intrusive manner, but they certainly weren't perfect. I've also used low-output moving coils directly into standard phone sections of preamps that were connected to high-input sensitivity power amps, yielding enough gain to avoid both a transformer and an additional active step-up, and this in many ways yielded the best results. You could do this in the analog days because tuners and tape decks had output level controls for level matching across sources. This worked because most American amps had ~1.5v input sensitivity so American preamps were spec'd at about 2 - 3v output at rated distortion. Most British/Euro power amps (e.g. Quad) had 0.5v input sensitivity and their preamps were rated for less than 1v output at rated distortion. So you could run a MC cart directly into an American preamp feeding a British amp and get adequate volume. Moreover, despite the specs, many MC carts of the day sounded better running directly into a MM input with the standard 47kohm impedance. Of course, you had to find the right pre/power combination to your liking.

Today, both the tube and solid state independent phono stages are better. There are excellent, musical silicon phono stages from Bel Canto, Trichord Research, Graham Slee, Sutherland, and many others, that won't bankrupt you. I've given up my transformer/tube phono setup recently because a move and some system changes made it impossible to get acceptable noise levels in any practical physical placement of the components. So I am using a Bel Canto Phono 1 driven by a Denon DL 103D, 60db total gain from the Bel Canto, and it's excellent. On balance, I have to say at the current state of development, it is better to go without a transformer and shop for a phono stage that can deliver sufficient clean, musical, tonally satisfying gain.

Keep in mind, phono is comprised of nothing but compromises. Low output moving coil cartridges are compromises themselves. A Shure V15 is and long has been measurably much more accurate from a frequency distribution perspective and of course delivering a much more usable signal, is easier to process. But moving coils have a character that belies the specs and once you find the right one, it's hard to go back to the MM sound.

You really have to consider the total amplification / gain chain to make optimal choices. But on balance, good transformers are quite expensive and if you put that money into a better phono section you can end up with less noise, more consistent performance, improved transient impact and generally more convincing fidelity, but some of the euphonic candy that comes with transformers will be missing.

Phil
Rather bizarre view that a step-up’s inability to conduct DC should be seen as a negative point. Especially considering that speakers, cartridges and amplifier have the same inability to conduct DC. Maybe we should get rid of them too?

Having recently replaced a stepped attenuator (i.e. discrete resistor) with a transformer-based attenuator in my pre-amp, it is glaringly obvious that a step-up introduces less coloration than even a single high quality resistor.

So how active amplification device, which will contain 1.) many resistors, 2.) many capacitors, 3.) many transistors and/or vacuum tubes, 4.) 30db (or more) of negative feedback (transistor phono), 5.) many different wires (or god forbid, pc boards!), 6.) many solder points, 7) a power supply (!!!!!) 8.) possibly a few regulators, etc, would induce less coloration to a low level signal than a single high quality transformer is simply bizarre.

Having built many amplifiers over a number of years, it has become clear that isolating the very small and fragile MC signal from noise and distortions emanation from the components of within an amplifier is not a trivial task. I have yet to hear a MC phono amplifier that does not raise the noise floor and rob the signal of some low level detail.

Step-ups are not perfect and will impact the signal with some residue. So does each and every component of an amplification device. Do the math.

Regards
Paul
Dougdeacon- bet you did not see that coming? Raul took a double shot tubes and transformers.