georgehifi
Responses from georgehifi
| Synergistic Red Fuse ... Pioneer receiver, two cheap floor standing speakers jammed up against the wall between a big screen TV in an almost bare room. Yeppers ... no improvement from the fuses at all. *lol* I can beat that, my stuffs all from Radio Shack or Tandy as i... | |
| Synergistic Red Fuse ... I replaced near new SR RED fuses for the SR Blacks and got a real significant further jump in resolution? Shakes head, many times. With all these improvements that fuses have bought, this system must sound better than anyone’s on the whole of Aud... | |
| Synergistic Red Fuse ... a top quality fuse. A top quality >$100 fuse may sound better than an aged fuse as stated, but so will a new 10 cent fuse, as switch on surge currents carbonise, stretch and sag the filament and change it’s characteristics over time with an ol... | |
| Synergistic Red Fuse ... Frankmlsstl656 posts03-14-2017 3:21amin the spirit of this thread, I thought I should warn people to NOT mark directionality on their fuses. The ink or sticker could confuse the electrons, drawing them off-center. The same is true of handling fus... | |
| Any comments on DAC going direct to power amplifier or to pre-ampliifer? Anyway, going directly into my Mcintosh MC205 obviously bypasses the subs and the result was predictable: very clear and transparent but bass thin. Plus I missed impact I get from the lack of subs, which I have time and phase aligned. You do wh... | |
| Too Much Power? Your Focal’s have a wicked impedance 3ohms at two power hungry points 80hz and 500hz, and a real bad -phase angle at 60hz which could equate a EPDR of 2ohms. Which is not real good good for a Class-D amp if you like to pump it up a little. I think... | |
| Synergistic Red Fuse ... "The fuse element is made of zinc, copper, silver, aluminium, or alloys to provide stable and predictable characteristics. The fuse ideally would carry its rated current indefinitely, and melt quickly on a small excess. The element must not be d... | |
| Synergistic Red Fuse ... "The fuse element is made of zinc, copper, silver, aluminium, or alloys to provide stable and predictable characteristics. The fuse ideally would carry its rated current indefinitely, and melt quickly on a small excess. The element must not be dam... | |
| Is my amp the problem? almarg 2)The miniDSP 2x4 has a very low input impedance of 6K. I'm going through the same impedance woes, with yet to arrive a Minidsp 2 x 4 HD to do some bass (<150hz) only experiments with, it's 10kohm input, a little higher than the 2... | |
| SE vs Balanced volume @steakster What is this amp??? That you got rid of Artemis 6c33c monoblocks for, I am intrigued.http://img.usaudiomart.com/uploads/large/1369416-cr-developments-artemis-mono-blocks.jpg http://img.usaudiomart.com/uploads/large/1369418-cr-developmen... | |
| Specific Pre-Amp advice darkstar1 OPExposure Dual 4 Reg has 24db of gain according to the President. That's a much higher input sensitivity than what your manual states at 1.2v. It's 50% higher.Cheers George | |
| SE vs Balanced volume because the signal coming in on the RCA connector together with the inverse of that signal provided at the output of the INA134 enables the input board to be provided with a balanced pair of signals. That means one phase only going to the "balanc... | |
| SE vs Balanced volume So what your saying then is the RCA input uses the IN134 to provide an extra 6db of gain to keep both inputs the same level, but there’s no feedback network to set the gain, and as the data sheet says it’s fixed gain at unity. Also then wouldn’t t... | |
| SE vs Balanced volume And also Al while were waiting for the OP's answer, I use two s/s amps with fully balance discrete input stage. This amp has rca inputs and xlr inputs with a switch between the two, no opamps involved. When switched to rca it just put’s pin 3 of t... | |
| SE vs Balanced volume Ok then it's now solid state, can the OP still post the make and model of it.? So we can put this to bed.Cheers George |