After looking at the manual for your phono stage I suggest the following:
1) Switches 1 through 4 for the left channel should absolutely/definitely/positively be set to the up position, which will provide the 47K load impedance your cartridge requires. If you have had any of those switches in the down position it would certainly result in major sonic degradation with this cartridge, and probably with nearly all other high output cartridges regardless of whether they are MC or MM. The corresponding settings should of course be made for the right channel, but BE SURE TO NOTE that those are controlled by switches 7 through 10, as the switch numbering is mirrored for the two channels (i.e. left 1 = right 10 and left 10 = right 1).
2) I suspect that left channel switch 9 (corresponding to right channel switch 2) would work best in the down (low gain) position, but depending on the design of the phono stage and the gains and sensitivities of the rest of your system it is possible that the up (high gain position) might be preferable in terms of noise levels and with respect to the positions of the volume control that you will find yourself using. It is also possible, though, that using the high gain setting would result in an obvious increase in distortion, due to overloading of the phono stage or the input circuit of your preamp or integrated amp.
3) The manual recommends that left channel switch 10 (corresponding to right channel switch 1) be left in the down (RIAA) position unless there is a problem with "cone flap" (i.e., woofer pumping) due to record warps.
4) After all of the foregoing settings have been optimized you can experiment with different settings of left channel switches 5 through 8 (capacitive loading), corresponding to right channel switches 6 through 3, which will affect tonal balance in the treble region. The unknown capacitance of your phono cable and tonearm wiring will affect what setting is optimal, which makes the optimal setting hard to predict. As does the vagueness of the "<500 pf" spec. But in any event be sure that the capacitive loading of the two channels is set to the same value; setting the values to be unequal would be an easy mistake to make given the mirrored numbering of the switches.
Regards,
-- Al
1) Switches 1 through 4 for the left channel should absolutely/definitely/positively be set to the up position, which will provide the 47K load impedance your cartridge requires. If you have had any of those switches in the down position it would certainly result in major sonic degradation with this cartridge, and probably with nearly all other high output cartridges regardless of whether they are MC or MM. The corresponding settings should of course be made for the right channel, but BE SURE TO NOTE that those are controlled by switches 7 through 10, as the switch numbering is mirrored for the two channels (i.e. left 1 = right 10 and left 10 = right 1).
2) I suspect that left channel switch 9 (corresponding to right channel switch 2) would work best in the down (low gain) position, but depending on the design of the phono stage and the gains and sensitivities of the rest of your system it is possible that the up (high gain position) might be preferable in terms of noise levels and with respect to the positions of the volume control that you will find yourself using. It is also possible, though, that using the high gain setting would result in an obvious increase in distortion, due to overloading of the phono stage or the input circuit of your preamp or integrated amp.
3) The manual recommends that left channel switch 10 (corresponding to right channel switch 1) be left in the down (RIAA) position unless there is a problem with "cone flap" (i.e., woofer pumping) due to record warps.
4) After all of the foregoing settings have been optimized you can experiment with different settings of left channel switches 5 through 8 (capacitive loading), corresponding to right channel switches 6 through 3, which will affect tonal balance in the treble region. The unknown capacitance of your phono cable and tonearm wiring will affect what setting is optimal, which makes the optimal setting hard to predict. As does the vagueness of the "<500 pf" spec. But in any event be sure that the capacitive loading of the two channels is set to the same value; setting the values to be unequal would be an easy mistake to make given the mirrored numbering of the switches.
Regards,
-- Al