Twisting wire on VPI for anti skate?


How do you make this twist? My manual (a great table but not a great manual at all) mentions it but does not say how to do it.
Twist it which way?
With no anti skating, all was well except one album that skipped on the first track.
rmcfee
the twist is made with the connector. Unplug the tonearm lead wire from the junction box and rotate it 360 degrees and plug it back in. If a loop forms in the wire, straighten it back out. Hope that helps
I wasn't really sure what caused it to skip. It is a mint album but I don't recall playing it before so it may have some flaws.
I have a VPI Scoutmaster 2 with the anti skate gizmo but it is disconnected.
The wire is supposed to apply AS force but there is no mention of set up. I will not use it if I don't need it.
It sounds amazing so I would rather not mess with it.
With no anti skating, all was well except one album that skipped on the first track.
A/S is intended to balance stylus pressures against the opposing groovewalls during play, not to prevent the stylus from racing down the angled slope of most lead-in grooves.

The key to preventing skipping during cueing is to keep the tonearm under control (manually) until the stylus locks into a groove. It would be a major error to use A/S for that purpose, you'd end up with far too much for playing the music.

It's debatable that A/S is needed at all. Many people including me don't use it at all. The test is not how does the arm cue, the test is how does it play. If you can track the toughest passages on tight inner grooves without R channel breakup or fuzziness, you don't actually need A/S at all. You may want some depending on your sonic preferences, but that's a matter for individual experimentation and listening.
My method consists of minimum anti-skate. First I set up the cartridge, for SRA, Azimuth and VTF, with no anti-skate. I also take a Digital Multi-Meter reading of the cross talk as a reference after setting azimuth. No twisted wire, fish wire disconnected. So now everything is set, VTF, SRA, Azimuth, and I have a reading of my cross talk with Azimuth set.
I have the VPI Classic 3, Dyna XX-2 MK II, VTF 1.988 grams. Crosstalk is -26.620db on the Left channel and -26.021 on the right. Azimuth is 0.19 degrees tilted to the right channel. SRA is 92 degrees (measure with a digital microscope).
With the SRA set (using the VTA tower), I make sure the fish wire is horizontal to the mechanical anti-skate.
Now I hook up the fist wire, ensuring the attachment point on the tonearm and to the top of the mechanical anti-skate is horizontal. I line it up, so I have one donut on the bottom, so I can put the fish line on the 4th indent from the top (first indent from the bottom). So one donut under the 4th indent from the top, the fish line on the 4th indent from the top.
Then I pull out the Hi-Fi news test record. I use the easiest bias setting test, Side one band 6, 300hz tone L+R, +12 db. When I play that with no anti-skate, left channel is perfect, the right channel will distort occasionally. I hook up the anti-skate and put one donut on the horizontal bar. I slide the donut out, until I don't get any distortion in the right channel on the +12db track. The one donut ends up close to the end of the rod. I don't even play the +14db, +16db and +18 db tracks. Those will lead you to nowhere.
So now the anti-skate is set, minimun with the +12db track. I then just double check crosstalk to ensure it is the same. I just want to be sure I am not twisting the tonearm in some way. This is probably an unnecessary step, since I have never noticed a difference in crosstalk, probably because I am careful about the horizontal setup of the fish wire.