2. amps-preamps
  3. 1042611447

If i had the money.....

I'd be ordering a set of the Parasound Halo JC-1 Monoblocks. I knew that these were going to be good, but i didn't know just HOW good. I've talked to a few people that have them and the "reviews" of these end users is just as strong as the recommendation that these amps receive in the February Stereophile.

Hard to imagine beating a product that was designed for optimum linearity / performance by an audio legend, laid out by an RF engineer in order to maintain consistent impedances throughout the entire circuit and then building the circuit with each part hand picked to "voice" the unit for optimum sonics by a "tweaker". The total approach to product building for $6K a pair !!! All of this with POWER to spare !!!

THD is predominantly all second harmonic i.e. not the typical odd order that most SS amps generate.

IMD of .0015 !!! Keep in mind that distortion typically goes up quite noticeably as power is raised and impedance lowered. This figure was taken at 4 ohms and at 600+ watts of output !!!

Output impedance of no higher than .06 ohms. This amp should keep the same "voice" and stability into just about any speaker. The power output verifies the stability and "robustness" of the circuit also....

Rated at 400 wpc @ 8 ohms

Power at clipping, broad band signal steady state:

8 ohms: 545 watts

Power at clipping, pulsed 1 KHz signal:

8 ohms: 586 watts

4 ohms: 1154 watts

2 ohms: 2255 watts

1 ohm: 4200 watts !!!

Any thougths / comments on this one ? Sean
>
sean
asa
626 posts
 
Well, I'm sure that these are very fine SS amps, and for the money - yes, for SS the stats do say something, and Bob Crump is upfront, skilled and not one for propaganda.

But even given that, Sean, I think you've gone off the reservation here with the circuit-tells-the-sound stuff as your point of departure.

I've never seen that view so prominent in your posts and wonder if your enthusiasm has gotten the best of you.

I'll second Tok2000. And, if you asked the Parasound's designers, then I'm confident, not coincidentally, that they would feel the same way about how to judge a component...
shubertmaniac
348 posts
 
From the literature it is Class A up to 25 watts and apparently there is an internal switch to bring it down to 10 watts if you do not want the heat. I think the JC-1s
are going to be the standard which all other solid state
amps will aspire for the price. I heard there will be a
matching preamp in the future. BTW, isn't the Blowtorch
preamp from the same set of designers?

Sean, as far as Spectral is concerned, I have NEVER had an oscillation. Neither the DMA50s nor the DMA200s have ever
had problems, oh I can blow fuses, but Spectral
stuff have tons of protection. And Sean, you can purchase
used a 200 watt DMA200 for under $2K! The thing is built like a tank and is absolutely drop dead gorgeous inside.
Personally I like it better than all Spectral amps
except the DMA360.
Idle is 800 watts, and it puts out the heat!
rcrump
427 posts
 
The bias switch is on the back and reduces the bias to the output stage....Most folks leave the amps on in low bias and then flip the switches to high bias when they are ready to do serious listening saving on the electric bill....Yes, CTC Builders designed and build the Blowtorch preamp....There will likely be a Parasound preamp......The JC-1 might as well be a CTC product as we were given complete freedom other than power output and the chassis design.....Nice project that lasted about three years including the work on the CTC BBQ (highly modified HCA-3500) we used as the mule for the JC-1....
sean OP
6,229 posts
 
Asa: I typically don't spend much time on specs because most people don't understand them or how they relate to each other. As far as "going overboard" on this specific product, i don't think that this is the case. If you look back to the last amp that i posted about after reading a review of it, it was the PS Audio HCA-2. I did make a big deal about the specs on this unit and how horrible and inconsistent they were. I also stated that i thought that specs could be interpreted to provide a reasonable idea as to how the amp might sound and react to various loads. Finding an amp that sounds good only in one system with one set of speakers with specific cables is a joke as far as i'm concerned. Looking at "real" specs can help you weed out those that lack versatility and are only suitable for specific types of loads. Sean
>
all_ears
20 posts
 
For those of you who've been reading my comments on other sites in recent months about the JC 1s, you may be interested that I put my money where my mouth is and bought them (from Bob). As if that wasn't enough, I decided to become a dealer and sell the JC 1s and a few other lines in my spare time.

Brian Walsh
Essential Audio
More to discover