2. amps-preamps
  3. 1276356977

Lightspeed Attenuator - Best Preamp Ever?

The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
georgehifi's avatar
georgehifi
4,966 posts
 

Hi hammering, you echo the responses of so many owners when you said.

"It simplicity (and price) impressed me so I took a chance and bought one. It has turned out to be one of my better hi fi choices."

This "kiss" is the way I like to keep it, to get the source signal to the poweramp/s with the least amount of colourations.
Rather than using preamp circuits, input switching, and volume controls ect, which all add their own set of signatures and colourations.

You should also give the $29 battery a try that I posted in my last post, as it is the purest way of powering the Lightspeed and will last a good 3 weeks before a recharge is needed, and please give us an A/B comparison if you get one between it and the supplied linear wall wart.

Cheers George
georgehifi's avatar
georgehifi
4,966 posts
 

I thank you also miller65 for your glowing response to your purchase of the Lightspeed Attenuator.

As for your question: "I have however noticed recently the display is showing what I believe is referred to as ripple and varies from 9.20 to 9.23 often changing every second or so , does anyone know if this is normal."

This will not effect the performance of the Lightspeed, as for two reasons, the Lightspeed itself also has an internal regulated 5vdc supply it runs on, so any slight fluctuations from your external supply will not have any effect on it’s stability, secondly the 30mV fluctuations you have on the display could be due to slight temp variations inside your Breeze Audio Linear power supply.

What you should do is also get the rechargeable battery I posted 2 posts back, as it will be the purest most stable noise free way of running the Lightspeed, and give us your opinion on how you like it’s sound, as for just $28 it’s a cheap experiment, and will leave no room for doubt as well. As we all know audiophiles have doubt if there is a question mark with anything, and it can eat away at our senses sometimes.


Cheers George



edbrux
1 posts
 
I bought two LA 's from George and I would want to share with you my experience.
I have in the past a numerous of preamps and my last one was a Audio Research LS 26 : having listened to the Lightspeed Attenuator I sold it.
The LA is so much better.
The LA may at first use sound " a little  britlle "  but when the impedance matched correctly it is amazing good and it beat all the preamps I had before.
Between my Audio Research DAC 8 and my Pass Labs amp it is a perfect match.
I am very happy with it - I can only say : try it
Thank you George.
miller65
3 posts
 
Thanks George the temperature variation in the power supply makes sense as it is more stable in line with a stable room temperature I also intend trying with a battery in the next few weeks.
As a next stage I am considering using my CD player as a transport and introducing a DAC into my system this will also enable me to include a network player at a later date. However having checked the output spec of the DAC Beresford Caiman mk11 I have a couple of questions in terms of how output impedance can effect the sound quality . The output voltage of the DAC is 2v which is in line with LSA recommendation but the output impedance is 1k ? appreciate it should be 200 ohms or less ideally . Iwill use with a very low capitance Stager silver solid i/c 0.5 metre length .
Does anyone have experience of using the LSA with output impedance this high and if so what if any effect can it have on the sound / volume control . I love the transparent dynamic sound the LSA currently gives me and wonder if this potential impedance mismatch would have any adverse effect on the sound quality or use of the volume control which 
currently operates at 12 o clock , which is generally plenty loud enough

dgarretson
2,394 posts
 

Hi George,  I'm thinking of an DIY LDR attenuator to replace the stock 10K Alps dual pot in a Sennheiser HEV70 energizer for HE60 electrostatic headphones.  I need to step down from 25Vdc to 5V for this application. The chassis is cramped and there is little room inside for a heat sink on the down regulator.  An LM2596 looks like an easy fit in terms of low heat dissipation and compactness.  Do you think this would compromise sonic performance relative to a LM7805 linear regulator?  My concern about the LM7805 is overheating from the 20V step down.

Thanks,

Dave  

More to discover