Dear Audiophiles!
I am looking for a solid-state class A power amplifier with balanced circuit topology to replace Acurus in my modest Hi-Fi setup:
Mac mini (USB3 output) ->
Singxer SU-1 ->
Yggdrasil DAC (AES/EBU XLR input) ->
Primare PRE30 preamplifier (AES/EBU XLR input) ->
Acurus A250 power amplifier (RCA input) ->
Monitor Audio RS-6
I am currently considering Pass Labs XA30.5 and am wondering if it will “work nicely” with my upstream and downstream components.
Any info/advice is very much appreciated. Please chime in!
Please see the specs below for your consideration.
Pass Labs XA30.5
Type: Solid-state stereo amplifier
Power Output: 30 wpc into 8 Ohm, 60 wpc into 4 Ohm (both 14.8dbW)
Power Consumption (Watts): 238
Temperature (deg C.): 53
Voltage Gain: 26 dB
Input Sensitivity: 0.77 V at 26db gain
Frequency Response: 1.5Hz–100kHz, –3db at 1.5Hz, –2db at 100kHz
Signal/noise: 150db at full power (I cannot believe this is not a misprint!)
Distortion: 0.01% at 3 watts, 0.1% at 30 watts (measured at 1 kHz)
Input Impedance: 30 kOhm balanced, 15 kOhm unbalanced
Damping Factor: 150 for an 8 Ohm nominal load
Maximum Output Current: 20 Ampere
Maximum Output Voltage: ±35 Volts
Output Noise: 150 microvolt unweighted 20 Hz - 20 kHz
DC Offset: <50 mV
Slew rate: ±50 V/µs
Dimensions: 19" (485mm) W by 7" (180mm) H by 19" (485mm) D
Weight: 62 lbs (28kg)
Shipping weight: 75 lbs (34kg)
Primare PRE30 Preamplifier
Balanced inputs 560mV
Line inputs 280mV
Sensitivity adjustment -20dB to +20dB
Tape outputs 280mV
Gain 16dB
Frequency response DC to 100kHz ± 0.1dB
THD <0.01%
Signal-to-noise ratio -118dB
Crosstalk -113dB
Mains 100/115/230V
Dimensions (WxDxH) 430 x 410 x 100mm
Weight 9.5kg
Monitor Audio RS6
Frequency Response: 38 Hz - 30 KHz
Sensitivity (1W@1M): 91 dB
Nominal Impedance: 6 Ohms
Power Handling (RMS): 120 W
Recommended Amplifier Requirements (RMS): 40 - 120 W
Tweeter Crossover Frequency: 3 KHz
Drive Unit Compliment: 1 x 6” C-CAM® Bass, 1 x 6” C-CAM® Bass Mid-range. 1 x 1” gold dome C-CAM® tweeter.
Cabinet Design: Balanced velocity twin reflex ported
Product External Dimensions: (H x W x D) 850 x 185 x 250 mm
Plinth Dimensions: (H x W x D): 25 x 255 x 305 mm
Individual Weight: 18 Kg
N.B. Impedance varies with frequency and goes to as low as 4 Ohms and as high as 16 Ohms. And, most importantly,“real” sensitivity is much lower than “nominal”: 87.40dB (averaged 300Hz-3kHz, 2.83V/1m)!
Measurements taken in the anechoic chamber at Canada's National Research Council can be found through this link:
http://www.soundstagenetwork.com/index.php?option=com_content&view=article&id=1221:nrc-measu...
