Initim,
I would guess the Venom would be better than the stock power cord. But, give them both a trial period.
ozzy
I would guess the Venom would be better than the stock power cord. But, give them both a trial period.
ozzy
Shielded power cord best used on Digital/Source or on Tube Amps?
Well I just tried the Furutech DPS-4 power cable with the Furutech Fl-50 Nano connectors. I hate to say this but it is a very, very, good power cable. Detail without brightness and a deep deep soundstage. Powerful full range and great dynamics. Actually the best power cord that I have tried.
I ended up buying 7 meters of the raw DPS-4 cable and decided to try my hand making power cables for my system. I also purchased the Furutech Fl-50 NCF Nano AC/IEC connectors.
I will also be obtaining some Nanotech 308 cable. This cable does not seem to have the extreme shielding that the Furutech does, so my plan is to use the Furutech DPS-4 on my Digital and front end source equipment and the Nanotech 308 with my Amps. Both cables are 11 gauge.
Is that what you guys recommend before I start cutting lengths? The Amp cables need to be 3M & 2M long.
Thanks,
ozzy
I ended up buying 7 meters of the raw DPS-4 cable and decided to try my hand making power cables for my system. I also purchased the Furutech Fl-50 NCF Nano AC/IEC connectors.
I will also be obtaining some Nanotech 308 cable. This cable does not seem to have the extreme shielding that the Furutech does, so my plan is to use the Furutech DPS-4 on my Digital and front end source equipment and the Nanotech 308 with my Amps. Both cables are 11 gauge.
Is that what you guys recommend before I start cutting lengths? The Amp cables need to be 3M & 2M long.
Thanks,
ozzy
- ...
- 33 posts total
Ozzy, The DPS-4 power cord is heavy and some what stiff. Although I find it easy to use on my amp and/or power conditioner that sits ground level I would be hesitant to use it on front end equipment that sits higher up in my audio rack and/or with light weight equipment. How are you stabilizing the DPS-4 power cords? |
@lak How does the DPS-4 compare to the FP-S022N in your opinion? Have you used both on the same component? I was able to ground the shield to the outlet end plug yesterday on the S022N and call me crazy but I do think it's better that way. I find I like it much more than the FP-S55N I've tried in the past but still not sure I prefer it over any of the CT blue/red/yellow cables as I really like what they do for my system. |
lak, I have no problem routing the DPS-4 cable and all of my source equipment is sitting on Stillpoints ultra SS. Minimum cable length should be 1.5M unless you have a straight shot then perhaps a 1M may work. In case others have problems with IEC’s coming out of the equipment here is a little trick. Put some teflon tape around the outside of the IEC before you slide it into your equipment. It will tighten up the connection and may provide some sonic dampening as well. ozzy |
@t_ramey, Over the past year, I have purchased The Furutech FP-SO22N ( Blue 14 gauge), FP-TCS21 (Green 14 gauge), FP-SO32N (Blue12 gauge), FP-S55N (Blue 10 gauge) and the DPS-4 (11-gauge) from Mike Kay of Audio Archon: https://www.audioarchon.com/. I found the Blue to be more dynamic and the Green to be a warmer and more laid back. On front end components I prefer the FP-SO22N (Blue 14 gauge). My DPS-4 is still in the burn in the stage, for a change I decided not to burn it in on my Audiodharma Cable Cooker. I have the DPS-4 currently on my Plinius SA Reference Amp, as Ozzy stated it sounded good directly out of the box. I'll report back later after burn in is complete and I have an opportunity to do some comparisons with the DPS-4. |
- 33 posts total