2. misc-audio
  3. 131672-481

The new Synergistic Research BLUE fuses ....

New SR BLUE fuse thread ...

I’ve replaced all 5 of the SR BLACK fuses in my system with the new SR BLUE fuses. Cold, out of the box, the BLUE fuses stomped the fully broken-in SR BLACKS in a big way. As good as the SR BLACK fuses were/are, especially in comparison with the SR RED fuses, SR has found another break-through in fuses.

1. Musicality ... The system is totally seamless at this point. Its as if there is no system in the room, only a wall to wall, front to back and floor to ceiling music presentation with true to life tonality from the various instruments.

2. Extension ... I’ve seemed to gain about an octave in low bass response. This has the effect of putting more meat on the bones of the instruments. Highs are very extended, breathing new life into my magic percussion recordings. Vibes, chimes, bells, and triangles positioned in the rear of the orchestra all have improved. I’ve experienced no roll-off of the highs what so ever with the new BLUE fuses. Just a more relaxed natural presentation.

3. Dynamics ... This is a huge improvement over the BLACK fuses. Piano and vibes fans ... this is fantastic.

I have a Japanese audiophile CD of Flamenco music ... the foot stomps on the stage, the hand clapping and the castanets are present like never before. Want to hear natural sounding castanets? Get the BLUE fuses.

4. Mid range ... Ha! Put on your favorite Ben Webster album ... and a pair of adult diapers. Play Chris Connor singing "All About Ronnie," its to die for.

Quick .... someone here HAS to buy this double album. Its a bargain at this price. Audiophile sound, excellent performance by the one and only Chris Connor. Yes, its mono ... but so what? Its so good you won’t miss the stereo effects. If you’re the lucky person who scores this album, please post your results here.

http://www.ebay.com/itm/ULTRASONIC-CLEAN-The-Finest-Of-CHRIS-CONNOR-Bethlehem-Jazz-1975-NM-UNPLAYED-...

Overall impressions:

Where the RED fuses took about 20 hours to sound their best, and the BLACK fuses took upwards of 200 hours of total break-in, the BLUE fuses sounded really good right out of the box ... and that’s without doing anything about proper directional positioning. Not that the BLUE fuses don’t need breaking in, they do. The improvement continues through week three. Its a gradual break-in thing where each listening session is better than the last.

Everything I described above continues to break new ground in my system as the fuses continue breaking in. Quite honestly, I find it difficult to tear myself away from the system in order to get things done. Its truly been transformed into a magical music machine. With the expenditure of $150.00 and a 30 day return policy there’s really nothing to lose. In my system, its like upgrading to a better pre amp, amp, CD player or phono stage. Highly recommended.

Kudos to Ted Denney and the entire staff at SR. Amazing stuff, guys. :-)

Frank

PS: If you try the SR BLUE fuses, please post your results here. Seems the naysayers, the Debbie Downers and Negative Nellie’s have hijacked the original RED fuse thread. A pox on their houses and their Pioneer receivers.

Frank



128x128oregonpapa
geoffkait's avatar
geoffkait
14,147 posts
 
Al, nice try. The nice legalese notwithstanding. 😄 Nobody including myself or even HiFi Tuning ever suggested the differences in measurements explain the audible differences among fuses. But it is evidence nevertheless. Everybody and his brother except for a few outliers now understands that aftermarket fuses sound better than stock fuses. 

And we also know SOME aftermarket fuses sound better than OTHER aftermarket fuses, for a variety of pretty obvious reasons, I mean unless one turns a blind eye to them or plays dumb. We also know - as HiFi Tuning states on their web site - that cryo’d fuses sound better than non cryo’d fuses and that fuses CONSISTENTLY measure and sound better in one direction than the other. It’s an undeniable truth. Whoops, except for naysayers. One would have to be pretty stubborn, who knows why, to ignore all the evidence that is staring him in the face. Obviously, it would be a hard pill to swallow for some folk. 😛 Now, I realize I’m going to get a lot of the usual 12 Angry Men reponse, "But you can’t PROVE IT!! 😡

You assume proprietary information would not be revealed? Huh? Why assume anything? As I’ve said before any company who reveals anything is making a big mistake. There is no requirement to do so and it only sets the company up for who knows what. This is not a peer review committee. This is not Journal of Physics. This is not the faculty at Harvard.
shadorne's avatar
Ag insider logo xs@2x
shadorne
7,333 posts
 
Al,

Even if there was an explanation (which there isnt), the obligation to design and build good equipment falls to the audio component manufacturer - that is where the big $$$ are spent by the customer. If a merely different fuse causes an audible change in an audio component’s sound then the logical thing to do is to get rid of the unreliable POS component! Obviously
fleschler
766 posts
 
geoffkait- I fully agree.with your comments.  

oregonpapa's avatar
oregonpapa OP
2,850 posts
 
Mapman sez:

" Kudos to Wolf for standing up to the bullies."

I had to laugh ... I've been called a shill, had my credibility questioned, demanded that I expose my receipts to prove that I've purchased the fuses in my system ... and I'M the bully?

I've been insulted to no end in these pages and even abandoned the original Red fuse thread in an effort to dump the naysayers who continue to crash through the doors ... and I'M the bully?

I HAVE to know how something works and unless I do, I can't be hearing what I'm hearing? For the umpteenth time .... I DON'T GIVE A FIG HOW THE FUSES WORK, only that they do.

Originally, I tried one RED fuse and was so taken by the improvement that I enthusiastically shared the results with other members here at A'gon.  That's it, pure and simple. 

To the naysayers ... Get a friggin' clue ... its none of anyone else's business how the fuses work. Denny owes no explanations to anyone. If he wants to give away trade secrets its up to him, but from what I know of Ted Denney so far, he's nobodies fool.

My take is that the fuses use graphene internally ... and graphene is known to eliminate micro-arcing. Micro-arcing, like micro-vibrations have the effect of smearing and degrading the sound. 

And by the way, why no response from dbarger regarding how I attained my fuses? Not that I had to, but I took the time and effort to answer his questions as completely and honestly as I could ... and not even a simple "thank you??"  Man, there's some strange folks lurking about. 

Here's an interesting article regarding graphene:

https://www.newyorker.com/magazine/2014/12/22/material-question

Frank
nonoise's avatar
nonoise
4,382 posts
 
@oregonpapa , don't give them the satisfaction of a reply. If they were in the same room, they'd be high-fiving themselves right now. Their hunger is insatiable and constant. I've been on the receiving end as well and do my level best to ignore them but sometimes you can't let the dumb stuff pass without a comment. 

Perservere.

All the best,
Nonoise
More to discover