Dose your Rega rp8 sagging issues


Hi everyone almost a year ago i bought the turntable of my dreams a rega rp8. I ended up pulling out some of my rsp so i could afford it. Once i brought it home i fell in love with it ever since. though over the past 6 months i noticed skeletal plinth started to sage to one side. I don't know is this alright to happen now my spindle bottom is starting to hit my rack shelf. Is this alright or should a guy complain back to the dealer about it? and has anyone had this happen to them?
128x128jakecanada
I have it sitting on top of a rack of silence and the shelf is a 1.5 inch peace of slate. So i know the shelf is not the problem. also the slate is perfectly level too before i place the turntable on top. And it seams its only the front left corner that sages. And all i use for a record clamp is a clever clamp no weight.
I would reach out to SoundOrganization.org - they are the US distributor of Rega.
JakeC - I'll be interested to find out how this turns out for you with the distributor.
Ugh.  I have an RP8 that is just over a year old.  I noticed that the spindle looked like it was touching my granite shelf as well.  If I remove the glass platter completely, it looks very close to touching. I can slide a thin piece of paper underneath the spindle, so it is not quite touching.  However, if I put the platter back on, it is obviously touching and I cannot slide anything underneath it.  I have tried it on different surfaces since it is so close, but the results are the same.  It does not appear that the plinth has sagged so much as the table was built with less than 1mm of clearance before adding the weight of the glass platter.  I am now similarly concerned and going back to my Rega dealer to get this worked.  Thanks for your posting as I am glad to know that my situation is not unique...
I did a bit of testing to understand where that 1mm or so of flex is coming from.  If I apply force to the spindle to the point where the the spindle touches, I can measure that almost all of that movement is coming near the the rear foot.  Of the three feet, that one has to absorb the most pressure from adding the weight of the platter.  In my theory if the plinth were flexing or sagging in the middle, then the height at the feet would stay the same.  However, since almost all of the height loss happens on the rear foot, it seems that the sorbethane vibration material in the rear foot is absorbing the added weight and compressing.

All 3 feet on the RP8 are adjustable, so I adjusted the rear foot to give me about 0.7mm of additional clearance.  That seemed to get me back up to the exact level I had before adding the weight of the platter.  I don't know if that is the right reference, but seemed to be a fair interim solution.  Unfortunately, even though the RP8 feet are adjustable, the threading is very thin and loose.  Also, the feet do not appear to have been designed to be used for leveling.  If I adjusted all 3 feet, the whole table would have a bit of looseness and wobble, so the table really appears to be designed to rest fully on the feet.

On another note, I have seen Rega push their wall mount shelf for their high end tables, and this could be a factor in how their design evolved.  That shelf is open with the deck only supporting the feet so that the spindle could never hit bottom.  That is not a practical option for me, and a table of this quality should not have this problem.

I am definitely going to press my dealer for an official response from Rega.  In the interim I have been able to fix the problem at least.  I have a spare set of isolation disks from another product that I am no longer using, so I have inserted one of those under each foot.  That has raised the table plenty so that the spindle doesn't touch.  However, if the table is compressing by about 0.7mm in the rear, that seems like a lot on a table in this price range.  I am not sure how that deviates from the reference design of the table for their "flat" setup, but I feel like Rega at least owes us some answers.

Thanks for your original posting on this as it helped me find a problem I didn't know I had...