2. home-theater
  3. 140231-120185

Denon AVR vs. Martin Logan Electrostats

My main speakers are Martin Logan "Source" (ESL electrostatic panels) added to a system powered by Denon AVR-X3000. Previous main speakers were Martin Logan SLM-XL (part of the Motion series), and volume was fine. Now with the ESL's, the AVR can't deliver enough volume, and because of the low impedance of these speakers, fear the AVR is struggling with the load. Martin Logan website recommends using 'quality' amplification, which they define as, "...nearly doubles power from 8ohm to 4ohm load, and doubles again to 2ohm load...". Denon says their "X" receivers nearly double power between 8ohm and 4ohm, but no mention of 2ohm (so I suspect 4ohm is their limit).

My question is, will an upgraded Denon AVR with more power (AVR-X4500H, or 6500H) supply the needed power to get the most of these Martin Logan's, or is a pre/pro required.

I am a fan of the Denon feature set (for HT), and have thoroughly enjoyed the X3000 for many years, so wouldn't mind upgrading if that will fix the problem. But anything above that (cost-wise) or loss of features is not the direction I want to go.

If Denon doesn't offer an AVR that will push these ESL's, then I'd rather replace the ESL's with something else. DefTech is out (can't tolerate the shrill sound of those aluminum tweeters), and I know from the Martin Logan SLM-XL's that I really like AMT tweeters, and am perfectly ok with any good soft dome. Most likely speaker substitute would be either Golden Ear (which I have auditioned - they are awesome and awesomely expensive) or Emotiva (which I have not heard) - both have good reviews. I have also heard Martin Logan Motion 60XT, but was underwhelmed (too bright and with cabinet resonance when pushed). 

Any thoughts would be appreciated. Hoping others with ML ESL experience could tell me straight if Denon AVR-X**** just won't deliver, and I need to go speaker shopping. Will be tough giving those up, if that's the case - these electrostatic speakers are truly amazing (even when underpowered).
128x128mwatsme
roberjerman
2,086 posts
 
Keep your Denon AVR-X3000 and use the pre-out jacks on it to drive a high-current power amp. There are several Perreaux 2150B's available now on EBay. 200wpc/8ohms, 400wpc/4ohms. Clipping at 300+wpc and 500+wpc, respectively. Can easily drive any electrostat! I bought one for use with my restored DQ-10's. Typical price around $700. 
reubent
3,587 posts
 
Just curious, did you re-run the HT Receiver Setup after inserting the new speakers into the mix? If not, do so to eliminate a potential setup issue causing insufficient power to go to the front L&R main speakers.

If the setup is correct, you can add a high quality power amp, using the HT Receiver pre-outs, as Robert mentioned. Remember, you will need to run the setup program again after inserting the power amp into the mix.
secretguy
199 posts
 
I use a Denon as well, though with much easier to drive speakers. My thought would be an upgrade, perhaps to one of the Anthem or NAD AVRs. They are generally of a higher quality....and cost, of course.
caphill
496 posts
 
@mwatsme

Your ML Source ESL electrostatic planar are prety awesome and I wouldn’t sell them and get Definitive Technology if I were you. Your ML Source ESL are better but the ML Source impedance is low their nominal impedance is below 6 ohms and its minimal impedance is below 2 ohms. That makes it hard on amplifier and there isn’t a single AVR that will be able to handle such low impedance and thus unable to drive the speakers properly. Upgrading to the top of the line AVR will not do any good.
You will need a good quality amplification (good quality external power amp or integrated amp) in order to do those speakers justice.

I recommend you sell your Denon AVR. Since you like features on the Denon you should highly consider getting a used discontinued Marantz AV8802 preamp surround processor (pre pro) that can be had for less than $2k in used markets. Denon & Marantz are sister company and they share same HDMI boards they have exact same feature sets same GUI, OSD, same setup feature. This Marantz AV8802 pre pro will perform and sound way better than any Denon AVR’s preamp processor section.

And for a five-channel power amp I highly recommend the Rotel RMB-1585 five-channel amp currently retails for $3k but you can find a used one for around $2k in used markets if you can find one. The Rotel RMB-1585 is a spectacular amp and will drive those ML Source ESL with ease and will sound very good very refined very musical and will be a major step up from any AVR’s power amplifier section, including the high end AVRs.

These Marantz AV8802 processor/Rotel RMB-1585 amp combo will elevate the performance of your system to a whole new level.
More to discover