Toslink or 110 ohm aes/ebu?


My aging Museatex transport broke down and I am awaiting delivery of a CEC TL51X. I use a bidat which was recently upgraded by John Wright. Because I also have a Wadia 170, which only has a coax connection, I used a VDH Octocoupler toslink between the transport and the bidat. With the CEC I can use either the toslink or a 110 ohm aes/ebu interconnect. Any thoughts on this as to which would make the better connection with this equipment and recommendations for which brand? I know the gospel here is to try different setups and see which I prefer, but I looking for recommendations as to where to start.
conedison8
In spite of your suggestion of Stereophile dishonesty I would rather trust their opinion then yours. Monarchy (second link) that measured jitter does not have any interest one way or another.

There are valid technical reasons why Toslink is worse. In order to have low jitter good transport is needed. Good transport have most likely transitions (coax output) in order of 10ns (average transport about 25ns) and limited bandwidth of Toslink causes smearing edges and introducing jitter especially when system noise is present. Regular Toslink has bandwidth of 6MHz reaching 9MHz for very good one. It is too low to output fast transitions.

It is all system dependent especially when Toslink breaks ground loops and I don't question that Toslink might sound better to you - just speaking in general terms.
Ive had a couple cec transports over the years .Ive run aes cables and ive run coax .Ive never used toslink before just cause of myth of them .Just remember this ,CEC has a transformer in the curcuit for aes/ebu to convert it.CEC has always recommended to use the coax out to any dac based on thats how they built the transport around ,although I used some great big name aes cables and loved it, the coax always beat it out in long run. So to answer your post heres the order. 1 coax, 2 aes ,3 glass,4 toslink , call anyone who repairs the cec and they will confer.Remember the less hardware in curcuit the better
I would suggest we should trust our "own" opinion above all else. In my experience of 22 years and having tried many good value and high-end pieces of equipment (e.g. currently Theta CB3 Xtreme DACS, Classe SSP-800, DVD-10AX, SCD-1 to name just a few) I have ended up sticking with a toslink connection. Perhaps part of the reason may be my reluctance to shell out $400+ for a COAX cable (maybe thats what it takes to get better sound) but the bottom line is that the 3 toslink inputs (in the CB3) are occupied while the coax inputs sit unused (unless forced to go that route due to 4th source component). Many of the criticisms of toslink have nothing to do with cable itself, more with how the output jack on the source component is designed. There is overemphasis on the solidity/rigidity of the connection itself, as stated earlier the intent is not to suspend a component by the cable!
In a nutshell- I prefer the toslink to coax in my set-up and furthermore recent experience with SSP-800 indicates that HDMI for audio is even superior (have to listen critically in 2-ch audio mode) but more on this later.
I always get the best sound in my system using AES/EBU Cables.

Interesting comments from people, I have an acquaintance in CA who swears by Toslink. Of course the noise in CA is much worse then here in Colorado over the power line and my friend feels that his system is much quieter when he uses the optical cables. I live less than 3 miles from the power plant and never found the advantage he did. Now SPDIF coax uses .5 volts while the AES/EBU uses 5 volts. I think the higher signal level makes for a improvement in signal to noise ratio. At least for me in sunny Colorado.
I'm running my upper end all analog, cd player-preamp-amp. Want to take a digital signal from my cambridge 840c, Toslink or SPDIF to a Behringer DEQ 2496 with AES/EBU or Toslink to do some bass eq then to another preamp to control volume .Everythang I've read say's Toslink stinks.Will investing in a Hosa cdl-313-SPDIF to AES/EBU converter work? sound ok?. And will cd player-processor-another preamp-amp line up be ok?Will an analog sub eq in place of the processor,analog from cd be beter?EQ's have phase shift.Digital path only one DAC. ?Toslink vs converter? ?Digital eq vs analog eq?