Tonearm for Teres turntable - approx $1000 - ??


I have way to much time to research for components for my new analog setup, and keep on thinking about new ways of spending my budget (which keeps increasing in size. :-( )

I have at least decided on the turntable - basically a Teres 160 - and the cartridge - Zyx R-100H.

I had decided on an Origin Live Silver tonearm,(with Twl's HiFi mod, of course,) too, but now I'm wavering about that decision. I can not afford to spend thousands of dollars on the tonearm, but can probably stretch my budget to about $1000. Used is fine... Are the Hadcock tonearms (which seem to be about the same price as the OL Silver) any good? Better than or equal to the OL Silver? Is there something better I should look for, or should I just stick with the OL Silver?
oakiris
The Belcanto is simply a renamed Scheu Classic Unipivot; it is available in either 9" or 12" length and can be wired up to your liking by Chris Feickert of Scheu. The price for the 12" version is around 700. I am ordering a new Scheu Premier II dual arm (9", 12") table with Classic 12" arm with the optional 80mm platter and a record clamp. The price for the whole rig inc shipping from Germany to Oakland, CA is 2495. Closest Teres with a comparable arm is many hundreds of dollars more.

The Belcanto/Scheu is a bit rough looking as TWL has mentioned to me. But, at the price I am taking a chance as it has received several excellent reviews. The other tonearms by Scheu (Cantus, Taco) are a bit pricey for what they are and I would look elsewhere at that price level.

The Morch is a good arm but has a lot of wiring breaks to accomodate the removeable wands and the detachable wire (DIN connection). I think it can be set up with a seamless wiring run if you order it that way. I would suggest you look at the UP4 if you have a non sprung table as it is significantly less money than the DP6 and many think the unipivot design performs better in any event. The DP6 is not a unipivot design.

An Origin Live silver with Audio Note silver wire in a seamless run might be the best bet for you. It is a good fit with a lot of cartridges and is not terribly difficult to install and calibrate. It also does not twist in your fingers as many unipivots do, which is quite disconcerting, when lowering the stylus to the record. First time I came across an unipivot was an Audiocraft AC arm; very weird. Performed quite well, though, on the Micro Seiki BL111

I would urge you to contact Chris Feickert at Scheu in Germany on the topic of arms and suitability. Chris sells Morch as well as the Scheu/Belcanto arms. He can also procure other arms such as the wonderful Schroder line
A standard wand is included with the Morch; if you get the precision (I would ) wand it is a bit more but not sure how much. Call Chris and he'll fill you in. Chris is very helpful (as is Hart at Audio Advancements) and will discuss your needs and make a recommendation appropriate. I never felt he was trying to "sell me" the Scheu arm. In fact, when I discussed a Morch UP4 he stuck with that until I expressly asked him about the Scheu arm; you know they are making more money on their own arm than a Morch.

Chris' email is:
webmaster@scheu-analogue.com

His other contact info is:

Dr. Feickert Analogue Products
Rütteberg 5
79294 Sölden - Germany

new workshop address
Rimsinger Weg 9
79111 Freiburg -Germany

phone: 0049-761-4598558
fax: 0049-761-484577
GSM: 0049-177-6013150
ICQ: 98121197
http://www.scheu-analogue.com
Not much luck finding a Morch tonearm - Music Direct said it takes at least 2-3 weeks to get one in, and the salesperson I spoke with didn't seem to know much, either, so...Couldn't tell me how much the Precision wand would cost, etc. Also, I must admit I am a bit worried about the possible problems with all of the wire connections.

Now I'm thinking about a (probably used) Graham 2.2 tonearm. This is one of the tonearms recommended for the Teres turntable. Do you think this would be a good match with the Zyx cartridge? Sorry - I couldn't find any specifications for this tonearm so can't calculate if it is the right compliance range with the cartridge.

OakIris
OakIris: Audio Advancements is the oficial Moerch dealer for USA and has a very personal service.

" Also, I must admit I am a bit worried about the possible problems with all of the wire connections. ".

OakIris: there is no single problem with the wire connections: it is like other tonearm and beats the Graham 2.2 performance for a lot less money.

The Graham was a design based on the high performance japanese Audiocraft tonearms, but the Graham people instead to manufacturer a identical copy they do some changes ( bad changes ) on it, that till to now can't correct, that's why to many Graham tonearm versions: 1, 1.5, 2, now 2.2.

The Moerch tonearm is based in the high performance japanese Highphonic tonearm. The difference here is that the Moerch tonearm is an identical copy of the Highphonic and that's why is so very good tonearm.

Is up to you.

Regards and enjoy the music.
Raul.
Rauliruegas - I am surprised that you feel the Morch DP6 is a better arm than the Graham 2.2, but am glad to have your input. I realize that a higher price is not necessarily the equivalent of better quality, but I haven't read any other negative reviews about the Graham tonearms and how they are poorly designed

I emailed Audio Advancements yesterday asking for more info. on the Morch; I've received no response as yet.