Balanced or single ended phono stage?


I'm currently researching phono stages but may not have the opportunity to demo them at home. I've taken a look at the Parasound JC 3 and the Ayre P-5xe which both have balanced outputs. I've also read great feedback about the Manley Chinook and the Audio Research PH-6 which can be found used for similar pricing used but are single ended.

My question is whether the balanced option should tilt me in favor of one type vs. another. I'm not too familiar with how important it is to consider balanced outputs when it comes to phono stages.

Current system is running balanced currently with a McIntosh C220 tube preamp, MC 402 amplifier and Ayre C-5xeMP SACD player, all hooked up balanced. I'm most likely going with one of the VPI tables in the classic line but haven't decided yet. Any good advice as to whether a balanced phono stage should make or break the decision since all the stages I've mentioned have great reputations?
audioguy3107
Dave, no worries. It was several years ago. Let me back up a bit.

I had a VPI Aries II TT when I picked up the Ayre P-5x. I did indeed order a custom made phono cable that was configured per the Ayre link you provided. The RCA end plugged into the RCA termination block on the Aries and the other end had XLR connectors for the Ayre phono. Worked well. I still have the 1/2 meter cables.

I don't think VPI had a XLR term block at that time.

I then picked up a used Triplanar VII which had single ended RCA connectors on the built in phono cable. After a while I realized that I had never flipped the bal/se switches to the single ended position! When I did it sounded a tad worse so I left them in the balanced position.

No doubt the change in gain made it hard to compare.

I later converted the Triplanar phono cable to have XLR connectors thinking it might be better. Again I did not notice anything after that process.

Curious, I pinged Ayre's Charles Hansen on Audio Asylum and asked him what was going on. It was a while ago but iirc he said with the switches in the "bal" position the negative or inverted part of the RCA input used of course for unbalanced inputs was allowed to float thus the inverted signal from the cartridge made it to the inverted input of the diff amp.

Not the best way, but as long as the inverted signal in the cable is allowed to float, never grounded, it works because of his design.

I did a quick search on the Asylum to try and find the thread but could not locate it. The search has some quirks to it and I will spend some more time tomorrow watching football.

Might be quicker to repost on the Asylum.

Hope that helps.
I too have heard that balanced is the way to go for a turntable source. When I recently switched from a good to moderate RCA to XLR cable outputing my phonostage, the XLR was clearly better.

This is gpoing to show my ignorance, but if the Phono cable has RCA not XLR connections. Does that not undo the benefit of XLR outs from the phonostage?
Some pretty basic reality:

1. There are many reasons for the quality of sound of a phono stage, differential design being one of many. Balanced might be beneficial, but many non-balanced phono stages beat balanced phono stages. This single factor certainly is not the most critical determinant.

I don't sell, make, or endorse any phono stage makers, I have absolutely no commercial or personal bias. I own both balanced and unbalanced phono stages.

2. Differential circuitry certainly does not eliminate cable influence.

* An inappropriate impedance will still be just as deleterious to the sound.

* A cable design that rings will still ring. And this sounds horrible, balanced or not.

* A cable with leading edge overshoot will still have it. And this too sounds horrible, balanced or not.

* A cable with changing impedance relative to frequency will still have phase distortion, balanced or not.

* A cable that rounds transients will still round those transients, balanced or not.

Balanced design does not change any of the above at all.

Years of interface design experience in high tech, outside of audio, is my background for this statement. In the audio field technical testing and listening confirm this.
Kiddman is 100% correct, but a preamble is really necessary to give his response context (as his truths apply to all circuits and cables).

There is rhyme and reason to cable design and geometry. This simple statement could spawn myriad tangents to this discussion, but as it relates to differential balanced circuits, ONE of the benefits of a properly-designed balanced cable is noise rejection.

Now, you can take any 3 pieces of conductor and connect the (+), (-), and ground and it will "work". But you ideally want the (+) and (-) conductors to be arranged symmetrically so that any externally-generated noise impacts the (+) and (-) legs identically. When the (-) leg is inverted and summed with the (+) leg, that noise cancels itself out.
I think your "preamble" is not "really necessary", as you state, to give my response context.

My assertions stand on their own, balanced is not a sonic guarantee of anything. Neither is it a detriment. Maybe it will be quieter in your system.

As for noise, not all is cancelled out. We often will see a circuit with additional parts. Not perfection! I have no horse in the race but I don't like "black and white" statements, high end audio is too full of them, and most of them are wrong. And if you have ground loops, balanced dies not kill those.

To get back to your original question, "My question is whether the balanced option should tilt me in favor of one type vs. another", don't let this one feature tilt your decision. I never heard it be the make or break for any phono stage, and I have tested a lot of them, including many of those reviewed as the best, and own a lot of them.

Listen to everything you can get your hands on, don't pre-judge or limit your field based on things like balanced or not, use of signal transformers or not, specifications, circuit design features claimed by the manufacturer, or reviews. Go to lots of concerts without PA systems, listen to solo instruments whenever you can, and try to match that feel.

Again, no connection to retail sales or electronics of any type. Just a guy who hates the hype in this industry. It's about the music. Don't get lost in the technical claims.