The CIA XDC-2 can be tried and returned for a refund (less restocking fee) if it doesn't work. That's where I'd start.
If you own other components with toroids, and if they don't hum, then you know the problem is confined to the one component.
If the CIA device doesn't work, then I'd consider buying a different amp rather than throwing money at a problem that's likely inherent with the component itself. |
Sorry if that confused you. The irony is that transformers hate to have DC provided to them on the inlet but they do a great job of eliminating DC on the outlet side. Then, it usually gets rectified anyway.
That's why I didn't suggest using an isolation transformer in front of the amp. Although it would probably solve the noise in the amp by eliminating DC to it, the iso tranny would be just as likely to hum. The problem might just be relocated. And I like iso trannys.
Should also mention that the reason you don't see a lot of the Channel Islands type of thing and why the DaBlok is DIY is because capacitors aren't intended for AC mains and there is a slight chance of the caps going "poof" or "bang". No, we're not talking dynomite here but it's scary enough for manufacturers. Thus, the heavy duty case, expensive components and the cost.
Have you gone to your breaker panel yet and turned off everything except the wall outlets to the stereo? Unpugged the TV cable and any dimmers or 2 or 3-way lights? You might find the source of the DC is something that seems completely unrelated.
Tvad is right, there are other causes for noise besides DC but I'm stickin' to my story unless you prove me wrong. Maybe even after that. |
Rakuennow
However, the consensus seems to be that all quality Toroids and modern electric equipment should be sufficient at removing DC.
Ain't gonna happen..... It's the nature of the beast. DC voltage interring the primary winding of a toroid transformer will cause mechanical noise. That is, if there is DC voltage on the mains. ========== The ones proposing DC as a main problem all seem to be selling something..
Nelson Pass nor Eva Manley are trying to sell devices to filter out DC voltage.
For a few bucks you can build a DC blocking filter as Pass and Manley talked about in their posts on DIY
==================
I'm entertaining, though, one alternative option. I could try to sell my Panamax "line conditioner", and buy a used voltage regulator, which should take care of magnetostriction, and to my underestanding, DC as well. Are there any opinions on this? I suggest you first check the back of the Amp and see what the manufacture voltage rating is. Is it 120V or 115V?
Even if it is 120V 10% under would put the voltage at 108V.
Then there is your meter...... How accurate is your meter?
>>>>>>>>>>
.
Ngjockey
Should also mention that the reason you don't see a lot of the Channel Islands type of thing and why the DaBlok is DIY is because capacitors aren't intended for AC mains and there is a slight chance of the caps going "poof" or "bang". No, we're not talking dynomite here but it's scary enough for manufacturers. Thus, the heavy duty case, expensive components and the cost.
Ngjockey, if it is a concern a fuse could always be placed ahead of the filter circuit.
. |
Here's a post from Roger A. Modjeski on AudioCircle.
"One thing to keep in mind about toroids. If there is any DC on your power line the transformer will audibly buzz and the magnetizing current will go up. This is because they have no air gap. EI transformers have an unintentional air gap of about .001 inches. That's all it takes to keep a transformer happy with a volt or two on the line."
This is exactly in line with my own experience: toroidals all hum/buzz to a certain extent; amps (e.g. most tube amps) that use different styles of transformer tend not to... |
I have a pair of Aragon 1Ks and one night I turned them on to hear a loud humming buzz comming from both units. I have a pair of dedicated 20 amp power lines running from the main household fusebox (one to each amp) so nothing else is on those circuits. Then I remembered my home theatre subwoofer making a similar humm/buzz when the halogen lamp in that room was set to half power - on the same cicuit as the subwoofer. So today I went across the house into the home theatre area and sure enough that same halogen light was turned on at half power, so I turned it off and the humm/buzz in my amplifiers dissappeared. Hence, even though it was across the house on a different circuit that light was still feeding DC voltage back through the main fusebox and into the dedicated lines going to my amplifiers. Hope this post helps others. |
