Transient Attack and Amp Design


I have observed with my new McCormack DNA-1 Deluxe (CJ Rev. 1 upgrade) that the transients are significantly better than my previous amps. Everything from classical, rock, and jazz has, for lack of a better term, better rythm and transients. (Granted, I have only owned mid-fi amps like Marrantz, Rotel, and Sunfire.)

I was wondering if the McCormack amp design explains the reason. It has eight caps on each output board instead of just one large cap for each channel. Maybe that means there is just more storage capacity? In any event, the amp is a heck of a lot more responsive than what I have heard in the past.

Is the multi-cap board topology more conducive to better transients or is this benefit dependent on the skill of the amp designer regardless of board layout?
jragsda
Now does the transistor proximity to the storage cap(s) make a difference?

Atmasphere can speak to that more knowledgeably than I can, but I don't think that would make a significant difference. The concern would not be propagation delay (which would be a few nanoseconds at most, as you speculated), it would be that the inductance of the wiring or printed circuit board traces between the capacitors and the output devices would slow the transfer of energy.

But I don't think that would be a significant effect either. As a very rough ballpark the inductance of one foot of straight wire is around 15 nanoHenries, which would have an impedance of about 2 milliohms even at 20kHz, and much less at lower frequencies. The numbers would be somewhat different if printed circuit board traces were involved, rather than discrete wiring, but I would think they would still be totally insignificant.

What would be of potentially greater significance would be noise pickup on those runs, but that is presumably filtered out by much smaller decoupling capacitors (that have much better high frequency performance than electrolytic storage capacitors), which should be and presumably are located very close to the point of use in the output stage area.

Regards,
-- Al
Jragsda, glad to hear you are enjoying your DNA-1.

I came up with the DNA (Distributed Node Architecture) design specifically because I do believe that it is audibly beneficial to eliminate (as much as possible) the connectors and wiring between the output devices and the source of their "instantaneous" current. At the same time, the capacitors used may be smaller individually and still add-up to a large effective capacitance. The capacitors still have to be carefully chosen for their audio characteristics, but it has been my experience that these physically smaller caps often have better audio performance (particularly at high frequencies) than their larger brethren. While it is difficult (or impossible) to defend this position from a strictly engineering / measurement standpoint, I note that a fair number of other amplifier designers have adopted this technique since the DNA-1 came out.

Best regards,

Steve McCormack
SMc Audio
Hi Steve, I think there is plenty of evidence out there to support your position regarding smaller caps!
Steve, at the risk of gushing, I am honored that you have responded to my thread. Kudos on an outstanding, musical amplifier in the DNA-1.

In the old Stereophile review (noted above in this thread), your DNA-1 design is noted for its treatment of distortion spectra. Here are JA's comments:
The Test CD also features signals with distortion spectra representing "tube"-type THD, "solid-state"-type THD, and a mixture of harmonic and subharmonic distortion typical of a planar speaker driven at high levels. My experience with generating the signals for the disc using the Audio Precision System One Dual Domain suggests that the situation is more complex than RH describes. While the DNA-1 does have some upper partials present, these are not isolated but are accompanied by the lower partials in an almost regular descending series. This is typical of tube amplifier performance, tending to sound smooth and "fat" rather than grainy.—John Atkinson
I suspect, but have not read, that you have departed from the "tube" distortion spectra approach in your later designs, notably the DNA-500. Is this so? If so, would you please comment as to your reasoning?
Alamrg

Inductance of 1 foot of straight wire is not 15nH. According to this calculator:
www.consultrsr.com/resources/eis/induct5.htm
it is between 330nH for 0.1" Dia to almost 500nH for thin wires.

Large capacitors have large inductance. Bypassing them with film caps creates parallel resonant circuit (inductance + lossless cap) that tends to ring. It is always better to use bunch of smaller caps in parallel to further reduce already smaller inductance and to lower resistance (ESR).

There are better quality caps like slit foil type (used in Hypex kits - very expensive) where foil has cuts to prevent eddy currents and to lower inductance (losses).

Power supplies require large capacitance because they are unregulated. Regulated SMPS running at 100kHz is fast enough to response to any current demand at 20kHz in spite of small capacitors.