Eminent Technology ET-2 Tonearm Owners



Where are you? What mods have you done ?

I have been using these ET2's for over 9 years now.
I am still figuring them out and learning from them. They can be modified in so many ways. Bruce Thigpen laid down the GENIUS behind this tonearm over 20 years ago. Some of you have owned them for over 20 years !

Tell us your secrets.

New owners – what questions do you have ?

We may even be able to coax Bruce to post here. :^)

There are so many modifications that can be done.

Dressing of the wire with this arm is critical to get optimum sonics along with proper counterweight setup.

Let me start it off.

Please tell us what you have found to be the best wire for the ET-2 tonearm ? One that is pliable/doesn’t crink or curl. Whats the best way of dressing it so it doesn’t impact the arm. Through the spindle - Over the manifold - Below manifold ? What have you come up with ?
128x128ct0517
Hello Chris, not an expert, but 33audio has an Acutex 3xx chart showing the actual size of each cartridge of the 3xx chart. This chart probably means nothing compared to the 4xx, but its all we have, and from there we only have speculation. The Acutex 415 seems on the literature to only have compliance difference's, but sounds nothing like the Acutex 420 according to Professor Timeltel, and he has never steered me wrong.

Your take on the Acutex 412 is like mine except the bass is strong like the 420. It has trouble with cymbals on my system. Mostly white noise. I never heard cymbal problems in music before, but someone mentioned it a while back and it has ruined a lot of good music for me, so maybe it is ok for others on there systems.
Hi Danny
Pictures of the Acutex 4 series can be seen here. Go down about 2/3 of the way down.

http://www.lencoheaven.net/forum/index.php?topic=6675.45

412 and 415 look like kissing cousins. 420 is very different.
I wasn’t clear in my last post. The 412 has lots of strong bass. The issue was it was over emphasized bass above 40 hz unlike the 420 which is more linear (sic) in my room on the ET2. This is based on running the 15 IPS tape and LP together, the lp about 5 seconds behind, and switching between the two on the fly.
Note that I was clear that this was a triple, not double leaf spring setup on an high pressure ET2 not a ET 2.5. ET 2.0 spindle resonates at a slighter higher HZ than the larger 2.5 which in my case now currently has the double leaf spring on it and my MC once more. The single leaf spring is just lying around these days. I should make up some more as they cost only $15 each. You can see the leaf spring hear. For a double, glue two together. Triple etc….

http://cgim.audiogon.com/i/vs/i/f/1335035482.jpg

We have Frogman to thank for this one. We are able to match the cartridge compliance at one end (cartridge) to the other end (counterweight) and use whichever leaf spring works best in our own systems. Think of it as two of almost same weight persons (cartridge end heavier) on an elongated teeter totter with springs on their bums.

As an update - yesterday afternoon one 420str was air lifted, scheduled to arrive this week at its destination. Tallahassee, Florida.
Addendum:
I have no doubt that if the ET2 manual ever got updated by Bruce, there would be a separate chapter on matching the tonearm with the compliance of the cartridge. Newly bought tonearms really should come with a single, double and triple leaf spring I beam.
Maybe they do ?
Both my ET2 tonearms were bought used.
Great link Chris, I had forgotten about it. Definitive comparison of the Acutex 3xx and 4xx.
Hey Guys, I've been quietly thinking of the next step in regards to my set-up with the Acutex. I've had several thoughts on it after re-reading your posts and thinking of how to better dress a wire loom. I still like my over the spindle option but have new thoughts on the support mechanism and wire/clips.
I want to implement the new support along with different cartridge clips first, so I can get proper cart set-up with my old wire loom, before building a completely new wire loom.
I also want to completely do away with the braid/shield I currently use. I'm thinking of a combo of silk/cotton tubing and/or teflon tubing as part of the support structure and vibration control scheme.
Any thoughts from you guys would be helpful.