Oyaide, Hubble, FIM etc, any consensus on flavors?


I’ve decided now to replace my hospital grade outlets with some more upscale outlets.

I’ve found thru the archives so far, there are several models in the Oyaide line up, and perhaps some of the others too, like Watt Gate, FIM, Isoclean, etc.

Something tells me they don't all do the same things

If someone could give me some inkling as to what each Oyaide model’s electronic flavor is, it would be greatly appreciated. Are there 3 or 4 models now out from Oyaide?

… but then I don’t know for sure as to which outlet from which co will give which results.

All lines are dedicated 20A

Main 2ch rig is all tubes.

Any insight on the varied flavors of the Oyaide, Isoclean, Hubble, FIM etc, would be immensely appreciated…. For at this time they all look alike to me except for their prices of course.

Naturally, I'd be inclined to spend more for the 2ch tubed rig, than I probably would on the HT side... but then, who knows?

so far the only insight I have is on the 3 Oyaide units:

1 Silver/Rhodium � Pure, strong, solid, uncolored reproduction � providing a very extended sound field.

2 Direct Gold - bold, sweet, luxurious, dynamic and lucid character

3 Gold/Palladium � the character of Gold with an added vibrancy and a cooler, fresher feeling Oyaide

...which I took from a resellers web page.

your thoughts?

Many thanks as always.
blindjim
I don't like to think that I can use a cable or outlet to push the sound in a certain direction. I just want to hear what's being played as close to the original as possible.

The Porter Ports and Avatar AfterBurner 8 outlet don't seem to affect the sound.

The Oyaide outlets seem to. I had the R1, the SWO-GX and SWO-XXX all in my system at the same time in my power conditioner and wall. According to which outlet I used, the sound would change.

I just personally don't like that, especially trying something plugged into this one, then that one, then the third one. Now, which one did I like the best?

The Porter Ports and Avatar AfterBurner 8 outlets are consistant, whether it's "neutral" or not, I like that.

Chuck

Chuck

Thanks much. That's also quite understandable if those are the guidelines for your systems development.

I find now and then however that some slight or minor alteration or enhancement/attenuation of a thing, via cabling or isolating, or tube rolling, to augment it's performance or simply to bring it into my own preffs range to a greater capacity by some minor tweaking is more desireable to me than to get back on the audio treadmill and seek out another set of speakers, amps, source, etc.

Also there is the component of increase. Overall increase or merely a partial one can be obliged in the same manner as I’ve just described. Perhaps one can call it allowing a thing to be at it’s best. Perform without any restrictions, or reducing it’s most glaring trait.

Naturally then I feel along with you to some degree that better peripherals all add into that mix… yet here and there still, perhaps one coloration in an accessory could be just the thing to polish the whole of it off.

Your replacement of outlets in that conditioner for example is a whole new idea to me and one I’d never have thought to do until now. Though I’m going to check with RSA to see which ones they used in their haley before I make any changes there.

I feel a rig is indeed a mixture regardless, when it’s all said and done… if it’s to come out of the oven done well.

Were the Avatar AfterBurner 8’s in any way better, or just the same but cheaper?

Many many thanks.
The Hubbell 5362 is a nice sounding outlet for not much money. Doesn't roll off the highs or "soften" the presentation like gold platings can do. Doesn't spotlight the highs like silver. Fatter bass and a little more "laid back" than rhodium.

In general, I've found that I tend to prefer un-plated high copper plugs and outlets in most places, though rhodium is ok in some spots. High copper, IMHO, is a very "honest" presentation.

I'd suggest starting with a high copper outlet (Hubbell, Porter, Jenna Labs, etc) and see how you like the presentation. Then, if you find something is missing, you can play around with various platings.

Mooglie

Thanks. That's good stuff on the copper aspect.

I'm currently onto this idea:
2 Porters
Either 2 Teslaplex or 1 each tesla & Oy R1.

I should get a fair cross section that way.

I am a mite hard pressed to believe an outlet can/will attenuate some part of the bandwidth though... and think maybe some part is not seen quite so prominent as perhaps the rest of it might be.

has anyone found any of these after market outlets a great choice for video? Like for a Front Projector?
I'm putting in a Porter Port this week. I'll let you know how it goes. It's going to be tough for me to decipher what's the Porter and what's a result of the new dedicated circuit. I might have to begin with the old $4 plug and then replace it with the Porter Port to hear what the differences are.