Is cheater plug safe with grounded monster power?

Artar1 -

Give me some additional information:

1. List the components that have a three-prong grounded power cord, including the substitutes.

2. Are you using dedicated circuit(s)?

3. Are you using a power conditioner? If so, which model?

4. Are all devices plugged into one circuit, or into more than one circuit?

5. Are you using aftermarket power cords? If so, which models, and on what gear? If you are not, please tell me what the wire gauge of each of the three-wire cords are. It will be embossed on the cord jacket.

Rex, On your question #1 please bear in mind that most Japanese products come with three prong plugs but few have the ground attached to anything. Many don't even have a third, ground connector at the unit.

Artar,

I recommend the following procedure to at least identify the culprit.

1. disconnect everything except the amp to speaker wires. Put shorting plugs into your main amp and turn it on. If you have no hum, the culprit is not the amp.

2. Connect the preamp to the amp after removing the shorting plugs. Turn the preamp on and then the amp. If you have no hum, neither are culprits.

3. Plug in one front end device. If you have no hum, with it active, it is not the culprit.

4. When you add something that causes hum, it is the culprit. It is possible that it is that unit's interconnects, so try others. Also it may be the only grounded front end device. Try a cheater plug. If the hum does not go away, try reversing the cheater. If none of this works, you have a problem with that device.

If the hum goes away with the cheater, which will typically be the case, you have an issue--do you need it grounded? Rex would answer one way and I another.

You might also find that grounding the unit to the amp may cause the hum to go away. Also a resister on the ground may solve the problem.

Artar1 - just FYI, if you have your equipment plugged into multiple circuits, Tbg's suggested procedure will not be of any help.

Tbg,

Thanks for responding to my post too.

I believe the culprit is the Muse Model 18, but it seems to work fine when the Klyne preamp and Musical Fidelity CD player are used instead of the Sony DVD player and the Proceed AVP.

”1. Disconnect everything except the amp to speaker wires. Put shorting plugs into your main amp and turn it on. If you have no hum, the culprit is not the amp.”

The main amp (Proceed AMP 5) does not hum, and it worked fine until the Muse Model 18 was plugged into the system.

”2. Connect the preamp to the amp after removing the shorting plugs. Turn the preamp on and then the amp. If you have no hum, neither are culprits.”

The Proceed AVP preamp also worked fine until the Muse Model 18 was plugged into the system.

”3. Plug in one front-end device. If you have no hum, with it active, it is not the culprit.”

The front-end device (Sony DVD player) also worked fine before the Muse was inserted. This leads me to believe that the Muse may be on another circuit from the other equipment and is, therefore, creating a situation in which there are multiple grounds.

”4. When you add something that causes hum, it is the culprit. It is possible that it is that unit's interconnects, so try others. Also it may be the only grounded front-end device. Try a cheater plug. If the hum does not go away, try reversing the cheater. If none of this works, you have a problem with that device.”

Using another set of interconnects is not an option. I am using two 12-foot pairs of Transparent Audio MusicLink Plus ICs that cost me $1,200. I can try reversing the cheater plug that I am using on the Muse to see if that suggestion works. Prior to installing the Muse Model 18 in my system, I had sent it back to the factory to be completely checked out. It was given a “clean bill of health.”

”You might also find that grounding the unit to the amp may cause the hum to go away. Also a resister on the ground may solve the problem.”

How do I ground a component to the main amp and how do I place a resister on the ground?

Thanks

Rex,

Thank you very much for responding to my post. I appreciate it!

Let me try to answer your questions the best I can.

“1. List the components that have a three-prong grounded power cord, including the substitutes.”

All components have a three-prong plug on their power cords except the Sony DVD player. So the Proceed AMP 5 amp, Proceed AVP preamp, Klyne System 7 preamp (substitute preamp), Musical Fidelity Nu-Vista 3D CD player (substitute CD player), and Muse Model 18 subwoofer all have a three-prong power cord. The Sony DVD player has only a two-prong power cord. I will check to make sure, however.

”2. Are you using dedicated circuit(s)?”

No. In the future I will, but not now.

”3. Are you using a power conditioner? If so, which model?”

No power conditioner per se; however, the Proceed AVP preamp, Klyne System 7 preamp (substitute preamp), and Musical Fidelity Nu-Vista 3D CD player (substitute CD player) are all plugged into a Monster Cable HTS 2000 power strip/line filer. The AMP 5 is plugged directly into a wall outlet.

”4. Are all devices plugged into one circuit, or into more than one circuit?”

I will have to check the breaker box when I return home tonight. But it’s my guess that all AC outlets could be on the same line. I am not sure about this.

”5. Are you using aftermarket power cords? If so, which models, and on what gear? If you are not, please tell me what the wire gauges of each of the three-wire cords are. It will be embossed on the cord jacket.”

I will have to check the gauge of all the power cords when I return home. I am using stock power cords on all components except the Klyne preamp, which uses a Monster Cable Powerline 300. In the near future, I will be replacing all the other stock power cords with Element Cable’s ElementCord, which uses 10 AWG wires.