It is a single_ended multichannel amp.
No option to run XLR cables.
Speakers will be rear/surrounds.
Amp cannot be placed near speakers.
No option to run XLR cables.
Speakers will be rear/surrounds.
Amp cannot be placed near speakers.
Can This Amp Power A 50 Foot Speaker Cable Run?
I'd like to run 50-60 foot speaker cables of 12 AWG cable to a pair of 6 ohm speakers for the rear channels in my home theater.
Would 10 AWG be better? The specifications on the amp says 6 ohms is the minimum impedance that it will play safely. Do you see any issues with this? Does the amp below seem to be up to this task?
Stereo Amp Specs are as follows:
Dynamic Power Output: 2 × 140 Watts at 8 ohms
Total Harmonic Distortion: 0.08 % at rated power
IM Distortion: 0.08 % at rated power
Damping Factor: 100 at 8 ohms
Input Sensitivity and Impedance: 1 V, 50 kohms
Output Level and Impedance: 1 V, 10 kohms
Rated Speaker Impedance: 6 ohms MIN
Frequency Response: 10 Hz – 100 kHz, ±1 dB
Signal-to-Noise Ratio: 110 dB (IHF A, 0.5 V input)
____________________________________
Infinity Kappa 7.1 Speaker Specs are as follows:
Nominal Impedance: 6 ohms
Power Rating: 30 to 250 watts
RMS Crossover Frequencies: 500Hz, 4.5kHz
Frequency Response: 39Hz-35kHz +/-2dB
Sensitivity: 89dB 2.8V/1 meter
Would 10 AWG be better? The specifications on the amp says 6 ohms is the minimum impedance that it will play safely. Do you see any issues with this? Does the amp below seem to be up to this task?
Stereo Amp Specs are as follows:
Dynamic Power Output: 2 × 140 Watts at 8 ohms
Total Harmonic Distortion: 0.08 % at rated power
IM Distortion: 0.08 % at rated power
Damping Factor: 100 at 8 ohms
Input Sensitivity and Impedance: 1 V, 50 kohms
Output Level and Impedance: 1 V, 10 kohms
Rated Speaker Impedance: 6 ohms MIN
Frequency Response: 10 Hz – 100 kHz, ±1 dB
Signal-to-Noise Ratio: 110 dB (IHF A, 0.5 V input)
____________________________________
Infinity Kappa 7.1 Speaker Specs are as follows:
Nominal Impedance: 6 ohms
Power Rating: 30 to 250 watts
RMS Crossover Frequencies: 500Hz, 4.5kHz
Frequency Response: 39Hz-35kHz +/-2dB
Sensitivity: 89dB 2.8V/1 meter
- ...
- 11 posts total
Speaker cable if they have capacitance get get higher in capacitance the longer you go, an amp "if bordering" on becoming unstable, "can" go into oscillation with the higher capacitance of long cable runs. To cite an amp that was bordering on being unstable, the original Naim 250 in fact went into heavy oscillation and blew up as soon as it was turned on, when it saw the capacitance of Quad ESL 57's presented. Cheers George |
@mitch4t you can still run balanced lines if you want. For something like this I’ve run the preamp into a set of line transformers at the preamp end, run the balanced cables can converted back to single ended using line transformers at the other end. You get a lot more resolution than you do running long speaker cables! Of course if all the amps are built in to the same box this means you will have to get an additional set of amps for the rear channels. Since that may not be practical there is another option which is often used in public address, which is to use transformers at the output of the amplifiers to convert to a much higher voltage. Then you run the speaker cables and convert back at the speaker end to the regular voltage. Take a look at this link: http://www.belden.com/blog/broadcastav/All-About-70-volt-Speaker-Systems.cfm |
- 11 posts total