Can stepup transformer be used with an MC phono stage?


I just purchased an Electron Images MCP-1 phono preamp and it seems to be a VERY good phono preamp;  however, I'm realizing it doesn't have enough gain for my .2 mV output Dynavector.  Doing a little more research, it seems that the MCP-1 works well for cartridges down to .5mV of output.  Could I use a stepup transformer between my cartridge and the MC phono input of the MCP-1 without causing any damage to the phono preamp or other equipment in my system?  If so, what specifications should I be looking for in a stepup transformer?

Thanks in response for any responses and advice.
wcheng2
To do this would be unusual in several ways.  First, because you only need about a 2X gain in signal voltage to get where you need to be in terms of input sensitivity, whereas most SUTs operating into an MM phono stage are designed and built to yield at least a 10X voltage gain.  But more importantly (second), the load resistor in your MC phono stage is most likely lower in value than that of a typical MM phono stage (47K ohms is pretty much standard for MM).  Typically an MC phono stage will provide an input resistance of about 1000 ohms and often much less.  When you hook up a SUT, you get a reduction of the impedance seen by the cartridge (defined as a resistance that varies with frequency) equal to the square of the turns ratio of the SUT.  Thus, if your phono stage has a 1000 ohm resistor at its input, and assuming you are using a SUT that gives you 10X gain (which would really be too much gain, but I don't know where you'll find a SUT with less gain), then the cartridge would have to drive a 10-ohm impedance (1000 divided by 100).  This means ideally that your cartridge needs to have an internal resistance of 1 or 2 ohms to be able to drive such a load. Only a very few MCs are that low.  If your stage has a 100-ohm fixed resistance (quite possible), you would really be in the soup; that won't work.  So, the first thing to do is to determine what is the value of the resistance at the phono input.  Second thing to do is to see if you can find a commercially made SUT with a gain factor less than 4 or 5.  (Gain is equal to the "turns ratio".) If the input resistance is high enough and if the gain of the SUT is low enough, you might have a fighting chance that your cartridge will drive it.

By the way, have you auditioned what you've got, or are you just going by the given specifications?  Because you're not too far away from a combo that might work as is. I'd give it a shot.
Ignore the above post it is irrelevant.

Your electron images phono is a pure tube unit with loading RCA sockets on the rear. The input impedance is more likely to be either 47k or open. You can measure the input impedance with a meter across the input with the unit turned off.

Tubes have high overload margins compared to solid state, and you can likely run a step up transformer but obviously you need minimal extra gain and my suggestion would be to run the unit as is - you might have enough gain anyway, albeit with a little noise ( which may or may not be significant ). If you try a step-up transformer, leave the loading plugs off.  

Let's see: You added to my information by guessing at the value of the input resistor installed in the OP's particular product.  Your guess of 47K is one of the possibilities entertained in my post.  After that, everything you wrote is in agreement with my advice.  Yet you manage to be insulting despite all of that.  You're true to form.
Guys...thanks for your responses;  both are very helpful.  The input impedance should be 47k or open since the unit uses RCA loading plugs for load.  I have been listening to the Electron Images phono stage with my .2 mV output (6 ohms internal impedance) Dynavector DRT XV-1s cartridge.  It does work; however, I have to turn the volume on my preamp to about 3/4 of full output to get satisfying volume.  It also seems that the dynamics and bass are somewhat muted, which I think makes me want to turn the volume up even more.  With another phono preamp that had 55 dB of gain, I was at about 1/2 of full output to get satisfying volume and dynamics, so my assumption is that the Electron Images must be  55 dB or lower.  Let's say it is 50 dB...if I used a stepup tranny of 1:10, I think the gain would be 14 dB...so 14 + 50 = 64, which I assume shouldn't cause problems since I see many phono preamps with over 70 dB of gain.  And I would likely be okay with loading since 10 squared = 100 and 47,000/100 would be 470 ohms.  Am I way off base with my math?  I'm also wondering if I could use some kind of loading resistor in the RCA plug to bring the 470 ohms down to 100 ohms...
Your math is good, and I'd say go for it. But you might want to double check on the load resistor value.  I do agree that the fact you have an RCA jack dedicated to adding an external load resistor suggests that the fixed value one is 47K.  Or "open".  You do want to know if it's open. Does the owners manual help?  Or just measure it.