2. amps-preamps
  3. 130932-96112

power for mc452 and c2600

I'm relatively new to high end audio. Had a mcintosh integrated amp for few years and now decided to upgrade to separates. Just received c2600 preamp and awaiting on mc452 amp due to arrive sometime next week. 

I don't know anything about power conditioners and protection devices. currently using monster surge protector. My questions: 

1. what is the minimum protection device that one would use for my equipment
2. does it have to be a power conditioner or just surge protection
3. how much do these "power conditioners" contribute to the overall performance? Can you objectively measure their effect? Can they worsen the performance in any way by limiting power? 
4. is there a real difference in relatively affordable (200-500) vs. higher price units (1000 and above) ? 
5. What are you using and what is your experience with it? 
6. Your recommendation on units with good reputation under $500

thank you 
ei001h
dlcockrum's avatar
dlcockrum
2,105 posts
 
Good discussion and I learn along with you.

Fully agree and understand both of your posts and think that you have invested in a proper solution for surge protection given the constraints of what is available in industrial power source products (or elsewhere to my knowledge).

MOVs are imperfect as you know, but at least the manufacturers of your products seem to recognize/acknowledge that they are known wear items (sacrificial in nature) and provide a warning system as they begin to fail. I shudder to think how many trusting consumers sit unaware as we write that the MOVs in their inexpensive "surge protectors" have long since ceased to provide any protection and are likely to be unnecessarily limiting current flow to their audio devices.

Dave
ei001h OP
67 posts
 
 I've learned a a lot from your comments and experience. Thank you. 

Getting a dedicated 20amp AC  line or the whole house surge protector is not feasible at this moment. I'm gonna stay away from cheap conditioners. I would like to begin with a simple and  a reliable surge protector without MOV. 

Lowrider, you mentioned you have a brickwell and furman. Which furman do you have?  

Which one would you recommend for my set up: (MC452, Krell KAV500, C2600, MX134, MCD550, Oppo 205) all mounted on a salamander synergy rack.

1. Brickwall 10-Outlet Rackmount Audio Surge Protector 
2. Brickwall Eight-Outlet Audio Surge Protector
3. Furman PST-8 DIG (I think this has MOV)
4. Furman PST-6
5. Furman SS6b
6. BPT Pure Power Center or PPC
7. CablePro - Revelation Power Strip 8
8. Hammond H1584H
9. Wiremold L10320, Power Strip

Has anyone used one of the above for an Amp? Any other suggestions welcome. I would like as many opinions as possible. Thanks 
lalitk's avatar
lalitk
1,105 posts
 
@ei001h,

I would highly recommend evo3-Sirius. It's very neutral and doesn't limit dynamics. It will be a ideal match for McIntosh components which are very clean and natural sounding components.

I believe you can try one in your system risk free from 'the cable company'. 

http://www.isoteksystems.com/products/performance/evo3-sirius/

ei001h OP
67 posts
 
Thanks Lalitk

In terms of protection, would isotek be better than the ones listed above? Do you have one? 
lalitk's avatar
lalitk
1,105 posts
 
ei001h,

While I have not compared your list of powerstrips with Isotek directly, my recommendation was based on various demos at Audio shows. They would have been a obvious choice for my 2ch/HT system if I wasn't so heavily invested in Nordost QRT system. 

I think you would appreciate the industry's leading best protection and exquisite build quality of evo3-Sirius power strip with MAC components. Should you choose to go with Sirius strip, I would also recommend DIY Furutech FP-S032N - 12 AWG PC with FI-11 connectors. 

It would be a pretty darn good power strip and you can thank me later :-)

PM me if you need help with the power cord, I will be happy to build one for you. 
More to discover