Vinyl heresy-overhang induced distortion is not that important


I have learned and am of the opinion that the quality of the drive unit, the quality of the tonearm, the quality of the cartridge and phono stage and compatibility/setting of all these things (other than setting overhang) and the setting of proper VTF, VTA, SRA, and azimuth are far more important than worrying about how much arc-induced and overhang- induced (the two are related) distortion one has. I learned this the hard way. I will not go into details but please trust me-I am talking about my new ~15K of turntable components for the deck itself and excluding cartridge and phono stage. I have experimented with simply slamming a cartridge all the way forward in the headshell, placing the cartridge mid-way along the headshell slots, and slammed all the way back, each time re-setting VTF, VTA, SRA, and azimuth. I would defy anyone to pick out the differences. I have 30K of tube separates, a Manley Steelhead, and DeVore O/93's. I submit that any differences in distortion due to sub-optimum arcs and deviations from the two null points and where they are located (those peaks in distortion) are masked several times over by distortion imposed by my tubed gear and my loudspeakers. To believe that your electronics and loudspeakers have less distortion than arc-induced distortion is unrealistic. I have heard startling dynamics, soundstaging, and detail with all three set-ups. It is outright fun to listen to and far preferable to my very good digital rig with all three set-ups. 
My point is that getting perfect alignment is often, not always, like putting lipstick on a pig, I think back on my days on owning a VPI Classic and then a VPI Prime and my having Yip of Mint Protractors fashion custom-made protractors for each of these decks and my many hours of sitting all bent over with eye to jewelers loop staring down horizontal twist among parallax channels and getting overhang on the exact spots of two grids and yet never hearing anything close to the level of sound I get now. Same cartridges, same phono stage, only my turntable/arm combination has changed. I kept thinking the answer had to be in perfect alignment when it was clearly everything else but.
Thoughts? I am sure I will get all kinds of flack. But for those that do tell me I am nuts, try my experiment sometime with a top-tier deck/arm combination and report back. 
128x128fsonicsmith
If tracking error was so very important to our listening pleasure; why with all the technical knowledge and manufacturing prowess we now have; are we not all owning linear tracking tonearms on all of our turntables? I would say that there must be far more important factors at play that would lead one to the logical conclusion that the tracking error must not be that critical of a factor in our enjoyment of spinning our records. But that's just my opinion.  
I've recently put a London Decca Maroon (mono) on the end of an Naim Aro, an arm designed around this very premise, which has no provision to adjust overhang having holes rather than slots. The arm board I have was made when I was using a DV17D3, the Maroon put's its stylus 2 to 2.5mm further past the spindle than the DV did so that is my overhang error. After optimising VTA and VTF as best I can by ear I can still hear the music sounds different (and preferable) half way across the disc compared to the beginning so I put the numbers into Vinyl Engine's tracking error calculator assuming 20mm overhang against the recommended 18mm and found the cartridge doesn't actulally cross a null point, but it's not far off half way through the side, the error at the first groove however was ~3 times greater than a correctly aligner cartridge would have. I don't find it unlistenable but I noticed it before I ever checked the alignment with the Feickert, it's enough to make me use up my spare armboard blank to correct it. This system is middling Naim (stageline N/282/Hicap/250) with a pair of Thiel CS1.6.
You mean I don't need to purchase the $700 AnalogMagik software, the $600 SMARTracker, the $150 torque headshell screw driver and spend a 1/2 day setting it up the cartridge to enjoy vinyl replay?  
In my opinion, you need to set up the cartridge properly with very good tools, and then find out for yourself if you think it makes a difference. This thread is a collection of anecdotal subjective impressions.
But you certainly don’t have to buy the analog magic hoo-hah or a smartractor, in order to have good tools for the job.