component cones/spikes vs. rubber


I'm trying to decide whether I should put cones/spikes or Vibrapads/pods underneath my woodshelving which is directly underneath my components?

(Note: I currently have wood shelves underneath my components so the spikes/pads will be placed in a platform config. All of the above will be sitting on an audio rack)

Components:
1. Cary CD player
2. Audible Illusions 3A pre-amp
3. BAT 75SE tube amp

Appreciate any comments/thoughts?

Thanks,
broken
My Star Sound rack is mounted on large cones, uses steel supports filled with very small steel bearings and the components rest on other steel cones. The whole thing is designed to couple strongly to the floor and transfer vibrations from the component to the floor by a direct route. This seems to work as there is a noticeable reduction in high frequency noise, things sound softer but clearer. But other paths work as well, my other rack is a VPI TNT stand and on this I have found FIM roller bearings to be very effective, as well as between my speakers and my Skylan stands. Dealer disclaimer, I sell [theoretically] the things mentioned but use them only as examples, as mentioned above there is no single way that suits everyone, they ALL sound different.
I don't have any experience beyond the Nordost Sort Kones that I recently purchased and put under my CD player, but I can pass along a story the owner of the audio store told me. You can take it or leave it.

He was helping a friend optimize a system that was getting some vibration related feedback though the turntable. They discussed several isolation ideas to keep the vibrations from the speakers from getting into the turntable. In the end, they used a set of Sort Kones and it was "cured." They were surprised that they worked in that situation, but very happy with the results. They use them under just about everything in the store.
Moon Gel is the answer. It is a product used by drummers and available in the big box music stores and on line. Cost about $6, so you have little to lose. Check it out. I use the product on speakers that are on book shelves.
I've found the Sort Kones to be more effective than even my Goldmund Cones, and I always thought the Goldmunds, given that they're a 20+ year old product, were as good as it got. I could clearly hear/lose emphasis, in particular, in a Nancy Wilson song, "Free Again." With the older Goldmunds, you could hear the bitterness when she sings,"lucky, LUCKY me...." She was, clearly, being sarcastic. With other feet, the punctuation, or "accent" if you will, was greatly dimished. I did find this to be tweeter dependent also, though. It was most obvious on a setup I did for a friend in California, where I sold him my old Mirage 490s,which have a titanium tweeter. Not so much so on other speakers, no matter that they were 5x as expensive as the Mirages ($600 back in 1990).
With the Sort Kones, much -- but not all -- of that sarcasm is back, but the speaker in the system now is the Nola Elite Plus, with the tweeters upgraded to the better, Alnico-equpped magnets.
In any case, if you DO get the Sort Kones, do NOT put them with their wider side under the equipment. Put the wider side on the platform: it allows the upper frequencies to "breathe" correctly and the ambience of the recording environment to appear. I had them upside down, with the "pointed edge" (not really pointed)on the platform, and kept wondering what happened to the fluidity of the low level detail. I then went back to Nordost's site (no instructions come WITH the Sort Kones) and read that they recommend the wider part be on the platform, not the component. A significant difference, sonically.
By the way, I think they're worth their price. I have the first three levels (one set each) of the Aluminum Steel, Aluminum Ceramic, and the Bronze and the difference is noticeable (the price is, too) and significant. However, one thing about these and ANY other footer: there is a spot where the vibrate correctly, and there are other spots where they will suppress certain frquencies. You MUST experiment. I have Walker's Brass thing-a-ma-jigs on top of the Nolas. If they're off AT ALL, they whole immediacy of the upper midrange/lower treble goes south, with the result that the 3D of your system crashes, ambience retrieval is retrieved OUT of your system, and the depth layering....well, FORGET depth layering. It was many months before I realized this. The same for Tube Traps. It's a pain, but it's the law of...what...physics? Or is that psychics?