Behringer DEQ2496 HELP

Thank you to the posters so far. Late last night, I had to try it one last time before going to bed; it was really bothering me. I experimented with the inputs...DUH! (hand slaps head).

I needed to put I/O on page 1 (input) to Pink Noise, not one of the others (I had optical). After this, it worked well enough for me to know that it will do the job, but I was beat and had to go.

I did let it run for a bit though, and it (the pink noise) seemed to go on for a pretty long time; I would guess at least 5 minutes. Is this expected/normal? The curve looked fairly different after but as I said, I had to go.

Thanks again! I look forward to playing some more tonight. I would also like to know if anyone has used analog in and/or out to the DEQ. I have seen many threads stating that digital IN is its strength, and I realize that, but curious if anyone has tried the analog with satisfaction. Reason I ask is I will be getting an integrated with a tape loop so that I can get all my sources on this machine, but with the easy ability to bypass it with a switch. (I think the bypass on the DEQ software is pretty easy too though).

Kck-
The pink noise runs until you hit "done". I was letting it go for about 5 minutes, but someone clued me in, now I let it go for about a minute in "fast" then another minute in "slow". That seems to be plenty.

Also, I use the anolog in/out. I have it between my pre-amp & amp, no problems at all. I couldn't be happier with this product.

Analog in and out is very high quality. The advantage of the digital interface is theoretical...maybe real but I can't hear it. I also have the DEQ2496 between my preamp and the electronic crossover going to the power amp. In general it would be better to put it in the TAPE loop (I don't have one) because the signal level would not be affected by the volume control. I avoid low signal level through the DEQ2496 by turning down the gain of the electronic crossover so that the preamp output signal is higher.

That's good news; I will try it in my new amp when it comes in. in the meantime, may I stretch my welcome with another question? (actually, that would make it two...)

From reading various threads I gather that you don't want to EQ below 100 (some say 80) hZ. I see the AEQ (or is it RTA) screen has zero dots below the 100 mark, and I see how to add them. The question is, after adding them, can I then tweak them (my choice is upwards). My rig includes speakers that are good to about 40-45 hz, but am also using a REL subwoofer that will go to 20. The REL is being run off the Neutrik connectors using the amps speaker terminals. There is no load to the amp as the amp's power is not used to drive these low freqs. Further, I read comments that say that EQ-ing below 80/100 hZ will also put a strain on the amp and speakers. How will the speakers get 'strained'... I mean, what they can do is all they can do, right? I understand if I am asking a driver that bottoms at 40 hZ to increase SPL in that range beyond the other freqs (assuming flat for this argument, which of course it rarely is). But if I ask that speaker to do 20 hZ flat, well it just doesn't care, right? OTOH, the amp should be able to pass that signal to the subwoofer, correct?

Kck...Below 100 Hz is probably a range where EQ is badly needed. The DEQ2496 suggests that the automatic equalization may not work well below 80 Hz, but for me it works fine.

Here are a couple of suggestions.
1...If you want more bass, turn up the subwoofer volume so that the DEQ2496 is cutting it down where needed instead of boosting.
2...Similarly, when you set up the "target" response curve, instead of boosting the low end try cutting the highs. The "ROOM CORR" function will do some of this for you.