The truth on low efficiency speakers like B&W?


I've been learning a lot lately, but I'm still questioning the true amp requirements for speakers such as B&W 802s. I've seen mentions of using 45 watt tube amps all the way up to 600 watt mono blocks. Seriously, what is too little and is a 600 watt amp over kill? Can the speakers ever be pushed hard enough to overcome an amp like the Parasound 2250 with 250 watts/ch @ 8ohms and 400 @ 4 ohms? Is heavy bass music require the upper ends of power? Thanks. Owners please chime in with issues you have had with low power amps.
rave426
No matter how powerful your amp is you'll never get bass from B&W 802. It's a unique speaker that doesn't benefit much from quality or quantity of amplification and it's a biggest looser in audio industry IMHO(pardon 801's bigger).
Well you have to consider the crest factor of high quality recording.

Excellent orchestral recording have peak to average ratios that can exceed 20:1, which means that the average levels are 20 times lower power than the peaks. If you like to listen at an average of 85dB at your listening position, which might be 4 meters from the speakers, well the power requirements add up pretty quick.

Let's say you have speakers that run 85dB/W. You're 4m from them, so the level drops to 73dB (6dB for each time you double the distance, 1m - 2m - 4m). So, to reach your 85dB, you now need 4W instead of 1W. Now, the crest factor of 20:1 needs to be factored in, which puts the power required on peaks to be at least 80W. If you want your average level to be 88dB instead of 85, then you need 160W peaks. Any amp that puts out less than that will be clipping.

For clean reproduction from speakers that run low to mid 80s and normal listening distances, you should always pick an amp with higher power reserve. 250W would be my minimum choice with speakers like that.

Speakers that run near 90dB and above can get by with amps of quite a bit lesser rating.
09-11-12: Elizabeth
Yes heavy bass played loud taxes amplifier power.
The "45 watt tube amps" are being used to play normal music at normal volumes. period.
The 600 watt amps are for dudes with small dicks...
As compensation. (i guess)
The Parsound seems to be in the middle, or 'reasonable'

Elizabeth, like I told you on our date at the beach, it was just "shrinkage"!

But seriously, I've measured 105db peaks at my listening seat on acoustic jazz played at realistic levels. I've also measured about a 5-6db loss between my listening seat and 1 meter from the speaker. Assuming a 4 ohm, 86db/2.83v/1-meter speaker is 2w at 86db, then 110db output at 1 meter would take 512w for a momentary peak. Some rooms aren't as lossy as mine and don't suffer much loudness difference at all between one meter and the listening seat, but some will suffer more. 105db peaks are, admittedly, very loud, and a lot of speakers can't comfortably get that loud anyway. Nonetheless, in a large room with a 4 ohm, 86db sensitivity speaker, 600w/ch is not entirely compensating for something. Of course, for Maggie owners this is an entirely academic conversation, because even a 20.1 doesn't sound very good at live listening levels. Or if your listening levels peak at, say, 97db at one meter, then a 45w amp will indeed work just fine. But a trumpet is louder on peaks than 97db at one meter, no less a rim shot on a snare drum.

Most of time I'm listening at 85db or less (mostly less) volume levels at my listening seat, and the highest peaks are in the 95-100db range, depending on the material. 45w/ch would be quite marginal, even under normal circumstances.
Whatever one's motivation, for better, complete bass at higher volumes, more power will only help and seldom ever hurt with speakers like the B&Ws.

If you only listen at low to moderate volume, you might get away with 40-60 good SS watts.

Tube amps + B&W speakers are not normally an optimal match from a technical perspective TTBOMK though some might still of course like the sound.