Triplanar is compatible with a Peripheral Clamp


I have just modified my newly mounted Triplanar VII UII so that it plays LPs coupled to the platter with my peripheral ring clamp in position.

I have a Clearaudio Master Reference with its dedicated Outer Ring (i.e. peripheral ring clamp).

Initial Problem: the Triplanar was ‘catching’ on the latter side of the Outer Ring when the cartridge was reading the lead-out grooves (i.e the silent grooves at the end of an LP).

Solution: The modification consisted of ‘filing off’ 2mm of the plastic black cap on the front of the lower tonearm tube.

Materials used: Riffler File (flat parallel filing area; rough); Needle File (flat parallel, No2 cut); Wet and Dry Sand paper (P600); Toothpaste; Ear Cotton Buds; decorators polystyrene sheet; acid free tape

Method: Modification done with the tonearm mounted on the turntable (i.e: no need to remove the tonearm for the modification). Tonearm secured in the armrest that (the armrest) was immobilised in position with one loop of acid free tape. With the exception of the black cap, the rest of the tonearm and turntable were covered with polystyrene sheet, secured in place with acid free tape.
Three consecutive stages of filing (Riffler then Needle then Sandpaper) followed by polishing with toothpaste on cotton bud resulted in a finish indistinguishable from the non-filed part of the black cap.

Time for the modification: 2 hours, mostly on securing the tonearm and the polystyrene sheet.

Limitations of modification: VTA range is *limited* to 10 full clockwise revolutions from the horizontal. With 11 full revolutions the underside of the upper tonearm tube catches the upper side of my peripheral clamp.

Acknowledgements: The modification above would not have happened save for the help of following three people:

Tri Mai confirmed to me that the black cap is solid allowing me to start filing without the fear that I will end up with an unsightly hole in front of the lower tonearm tube.

Atmasphere provided me with a new L-bracket when the screw in the old one got stuck.

DougDeacon provided me with a list of possible solutions to the problem of operating a Triplanar with a peripheral clamp; in that list the absence of any documented Triplanar tweaking solving the problem allowed me to brainstorm the above modification.

Any criticisms or contributions to refining the above tweak will be greatly appreciated.

Many thanks in advance
kostas_1
oh ... and to the original poster. Nice work. I appreciate your passion.

Cheers,
Thom @ Galibier
Hi Thom,
I agree with your assessment of ring weights. In fact, on balance I could live without record weights, record clamps, AND peripheral ring weights. (I now never use either of the former, occasionally use the ring.) Not only do they add to the necessary ritual of playing an LP, in my system they also can rob the music of some sense of liveliness that I delight in. I guess there is a point where excessive damping of resonance is not such a good thing.
Interesting thread. A friend owns a TTWeights Gem and tried mounting the Tri-Planar and when used with an outer ring found out about the problem mentioned above. He called the designer and was told to move the arm back by about 2mm and readjust all other parameters and then he could use the ring. The designer thought that not having the arm set at the exact 233.5mm pivot to spindle distance was a better option than not being able to use the outer ring clamp.
Thoughts by others of this solution?
Mounting any tonearm at a non-designed distance from the spindle necessarily alters the alignment geometry. It will be impossible for the stylus to track the arc across the platter that was intended by the tonearm's designer.

If an arm must be mounted farther from the spindle then the cartridge is normally moved outward in the slots by a similar amount. This allows zenith to be aligned at the points the arm was originally designed for (Baerwald for a TriPlanar), albeit with a flatter tracking arc. This in turn necessitates skewing the cartridge slightly in the headshell.

Whether the tiny reduction in tracking angle error from the flatter arc would compensate for upsetting the arm's intended force vectors from a skewed cartridge is impossible to predict with certainty. Personally, having heard both misaligned cartridges and rigs played with and without rings, I wouldn't bet on it and would want to compare.

BTW, whether it would even be possible to attain the TriPlanar's intended Baerwald alignment in your friend's setup will depend on the stylus-to-mounting screws dimension of his cartridge. Some cartridges wouldn't be long enough to attain alignment with the arm moved that far back.

I hope the designer knew which cartridge your friend was using and that it was in fact long enough to be aligned with the arm mis-mounted by 2mm. If not, his advice was in effect a statement that, "My ring is more important than aligning your cartridge properly". Unless he's tried it himself with the same cartridge and tonearm, he couldn't know that and his advise would be merely self-serving.

Even if he did know the cartridge could be aligned, I hope he advised your friend to compare the sound with (a) the arm and cartridge mounted normally, without the ring, and (b) the arm and cartridge mounted abnormally, with the ring. These setups would certainly sound different but I doubt anyone could predict which would be "better".

When forced to choose between compromises, the user should listen and decide for himself (or resolve the problem with radical methods, like our brave friend Kostas).