Where can I hear Teres


I have read alot about the Teres TT,where in the name of
god can I hear one?
taters
As I mentioned before I have never seen or heard the Teres in the flesh so I would never claim that the Redpoint actually sounds better than the Teres. I suspect that both tables are quiet good and most likely a much better value than anything you can get through normal distribution channels for comparable money. After meeting the people involved with Redpoint I was very impressed. The Testa Rosa sounds incredible in my system and I cannot imagine having the desire for a better table. I am sure that if I had chosen a Teres I would probably feel the same as well. Its very refreshing to have these type options in an industry that seems to have many products priced way too high.
Jyprez, I remember that post. It seems the acrylic may not take a liking to the mineral oil. And the brass plugs may not contain it. Redpoint seems to have designed their platters around the concept of them being filled with oil, hence they are sealed.

Peter from Redpoint mentioned that he has tried every thing from thick motor oil to alcohol as a filler and they've settled on something in-between.

I don't know Peter but he seems to be a maniac when it comes to tweakery. Everything he claims to have done to the table is simply as he put it, "because it sounds better". He is driven to push the design to its maximum potential.

I am sure both the Teres and Redpoint are fantastic in their own rights - regardless of the materials chosen. But.. if I were to go out on a limb, I would say that the Teres base (or almost any lead shot filled wooden base - Cocobolo, or maybe even Ebony) with the Redpoint bearing system fitted into the wood base (via custom threaded insert), the Redpoint Teflon and Aluminum platter, and the Redpoint motor....

(Not to fault the Teres motor design *I* just don't like the idea of a sensor - hunting for speed all the time. The Redpoint "solves" this with a speed dial.)

Anyhow, that could quite possibly be the hot setup - taking the best of both designs. That said, I have often found that a "team of allstars" doesn't always perform as harmoniously as logic dictates it should. In any given system - audio or otherwise - there are weak links which are counterbalanced by stronger influences. Ultimately a system or design is simply a sum of its parts and how those parts interact with one another.
A few minor corrections to a good thread.

The Teres bearing housing is 1.5" in diameter.

The original Teres bearing used a delrin thrust plate. We switched to teflon coated brass about 18 months ago. We found that the brass sounds quite a bit better, at least in the Teres that is.

I tried the oil and lead approach and found that it did indeed sound marginally better. However, there were some issues. Oil is actually a little more difficult to contain than it may seem. The seal must be very good or it slowly seeps out. I ended up with a thin film of oil on the bottom of the platter after just a couple of days. Another issue for the Teres platter was simply cosmetics. No way to get the bubbles out and it just didn't look very good. I thought that the sonic gains were just too small to justify leak hassles and the cosmetic loss. Sorry to be too pragmatic but I do think that cosmetics matter, so long as they are kept as a minor part of the equation. To put things in perspective, a cap change in the motor regulator circuit made a bigger sonic impact than the oil.

The Teres motor has a clever way around the "hunting" issue. Once the speed locks in the controller switches to a mode where the voltage can only change a few millivolts per minute. This is just enough to compensate for some slow drift. Once the speed is locked it sounds identical to a fixed regulator. The sound of a fixed regulator but no need to adjust.
--
Chris
Chris, Thanks for the additional information. (It is good to hear both sides regarding this technology)

Regarding the bearing housing being 1.5" in diameter. I am a bit confused because the Teres site says, "The Teres bearing mounts via a 1.125" diameter threaded mounting stub (see drawing)."

Did this change?
Bryan, the bearing housing is not actually the mounting stub. The bearing housing is above the mounting stub, and the stub is just the connector that goes through the plinth. They are all one piece, but the upper part houses the bearing and the lower part is the mounting stub. Also, even though I don't want to turn my TT upside down right now, I think that the nut that holds the bearing mounting stub to the plinth is more than 1/8" on each side. It is a large nut with plenty of surface area to hold real tight. And the bearing housing shoulder that hugs the plinth on top is the 1 1/2" part that makes an excellent "clamping" arrangement for holding it to the plinth. No problems in that area.

As far as Redpoint's negative comments about the Teres, I say let the market be the judge. Also, notice that Chris was very objective in stating the reasons for his design decisions, and made no derogatory references toward Redpoint.