Where can I hear Teres

Chris, Thanks for the additional information. (It is good to hear both sides regarding this technology)

Regarding the bearing housing being 1.5" in diameter. I am a bit confused because the Teres site says, "The Teres bearing mounts via a 1.125" diameter threaded mounting stub (see drawing)."

Did this change?

Bryan, the bearing housing is not actually the mounting stub. The bearing housing is above the mounting stub, and the stub is just the connector that goes through the plinth. They are all one piece, but the upper part houses the bearing and the lower part is the mounting stub. Also, even though I don't want to turn my TT upside down right now, I think that the nut that holds the bearing mounting stub to the plinth is more than 1/8" on each side. It is a large nut with plenty of surface area to hold real tight. And the bearing housing shoulder that hugs the plinth on top is the 1 1/2" part that makes an excellent "clamping" arrangement for holding it to the plinth. No problems in that area.

As far as Redpoint's negative comments about the Teres, I say let the market be the judge. Also, notice that Chris was very objective in stating the reasons for his design decisions, and made no derogatory references toward Redpoint.

TWL - thanks for pointing that out. Also, I agree. Chris is a true gentleman and very informative! Always.

My math skills are lousy but I'll give this a try...
Assuming the nut which secures the bearing to the base is a hexigon, measuring 1.725 diameter (from Teres website) and threads around a 1.125" spindle. I estimate this would provide .3075" (slightly less than 5/16) of contact at the widest point on each side of the bearing and .1825" (slightly less than 3/16 but closer to 2/11).

This means that the average contact area of the nut would be .245" or ever-so-slightly less than 1/4". Which is double what was suggested.

The Teres Bearing Mounting Stub is 2.5" long and from the pictures I just looked at (in the 200 series manual)shows the bearing sitting inside the "mounting stub" at what appears to be a 1" depth. So since the bearing housing of the Teres bearing differs in diameter for the reservoir and the mounting stub making a statement that the bearing housing is X diameter is not exactly true is it??

While it sounds better to say the bearing housing is wider (or as Redpoint put it - the Redpoint bearing is a Teres bearing on Steroids) but does it really matter? Honestly now.

Bryan, thanks for the calculations. I was sure that it was more than they were stating.

Regarding the massiveness of the bearing housing, it is at the point where it is so massive already, that I really don't see why any larger is better. The Teres bearing totally dwarfs the Linn bearing that you have on your table right now. It is like a 747 next to a Cessna 150. I would say that the whole matter rests upon the sonic performance. Nothing else is really germaine to the discussion, except maybe appearance. If these "improvements" are not sonically better, than what purpose do they serve? I don't know if they are or not, but I have my suspicions. My suspicions are that Teres and Redpoint are targeted at similar markets, and that Teres has achieved better penetration of that market. Redpoint is playing "catch up". Apparently they've decided that "attacking" the competition will steer sales in their direction. I doubt it. I think that Redpoint is suffering from "styling" difficulties that will not allow it to penetrate into the high-end audiophile market, as its appearance will visually detract from many high-end systems. This is a major consideration in design, and one they have not yet mastered, in my opinion. Whether it sounds as good as a Teres, I don't know.

Twl, I have read many threads you have participated in and respect your opinions regarding analog systems. You obviously do not like the industial design of the Redpoint product. Before buying I had checked out the Teres website and was turned off by its wood base and clear platter with visible lead shot. Was just not my cup of tea, I guess to each his own. I will say that the Redpoint Testa Rosa is much better looking in person than in the photograph on the website. I do not much care for their Quatro TT design although it does sound quite good. Also I feel that several on this website are accusing Redpoint of bad mouthing the competition. All I will say about this is that in multiple meetings with my contact at Redpoint and discussions regarding his association with Teres not once did he ever speak negatively of Chris or his company. I am sure that they feel that they have done some things that are an improvement over other turntable designs, after looking and listening to their tables I tend to agree although this is very subjective and others could disagree.