I have a set of Martin Logan Aerius i's. I have had them for 5 years and have been biwiring them for about two years now. Switching to biwire configuration made an instantly recognizable change to the sound, larger, in my experience, than changing the interconnects or the type of speaker cables used. To me, the sound really opened up and the bass tune and definition really improved. I have no idea what the technical reasons for this are, but the difference is quite large and apparent to anyone who listens. It may be possible that the improvement i am hearing is actually some kind of "static" and "stochiastic" distortion creating a "false sense of air" but every time I try going back to single wire, even using high quality jumpers, I don't like the sound. If it's distortion, so be it.
Why bi-wiring is bad
From a link at the Chris Van-Haus website:
THE DISADVANTAGE WITH BI-WIRE
One thing that happens when you biwire your loudspeakers is that the input of the high- and the low-pass filters are fed with different input signals. The difference is a result of the high frequencies and the low frequencies being forced to travel different paths, perhaps through different types of cables, but under all circumstances through cables who have seen different loads (a tweeter with a high pass filter has a completely different impedance response compared to a woofer with a low pass filter!).
What happens is that the drivers will work less good together than when their filter halves were fed with equal signals. The result is a generation of more static and stochastic phase error sounds at different directions from the loudspeaker. The stochastic phase error sounds appear because there may be different types of unlinearities in the low- and high-frequency paths.
What does this sound like? Well, usually, just as you may expect from physics, it appears as a change in the reproduction of space and sound stage. Often, the first impression is that the "biwired" sound presents extended "dimensions", more "air", and is more "living". The impression after a week or month, however, is that all recordings sound very much alike, and the "airiness" appears on all records. It does not even sound like air anymore, instead more like a slime that pollutes every record you play. No wonder, since it is not a real, recorded quality but a "speaker characteristic" added to all reproduced material. "Sameness" is another word for it.
I just went back to bi-wiring over the weekend. The first thing I noticed was cymbal-like instruments shimmer much more. Secondly the bass now seemed to be less perhaps due to the greater high frequency information.
On orchestra music the orchestra is now well behind the speakers instead of right at the speaker. Like the article said, this may be a phase or time shift error and the depth may become wearing over time.
Finally there is slighlty better separation between instruments. It's easier to pick out each instrument.
THE DISADVANTAGE WITH BI-WIRE
One thing that happens when you biwire your loudspeakers is that the input of the high- and the low-pass filters are fed with different input signals. The difference is a result of the high frequencies and the low frequencies being forced to travel different paths, perhaps through different types of cables, but under all circumstances through cables who have seen different loads (a tweeter with a high pass filter has a completely different impedance response compared to a woofer with a low pass filter!).
What happens is that the drivers will work less good together than when their filter halves were fed with equal signals. The result is a generation of more static and stochastic phase error sounds at different directions from the loudspeaker. The stochastic phase error sounds appear because there may be different types of unlinearities in the low- and high-frequency paths.
What does this sound like? Well, usually, just as you may expect from physics, it appears as a change in the reproduction of space and sound stage. Often, the first impression is that the "biwired" sound presents extended "dimensions", more "air", and is more "living". The impression after a week or month, however, is that all recordings sound very much alike, and the "airiness" appears on all records. It does not even sound like air anymore, instead more like a slime that pollutes every record you play. No wonder, since it is not a real, recorded quality but a "speaker characteristic" added to all reproduced material. "Sameness" is another word for it.
I just went back to bi-wiring over the weekend. The first thing I noticed was cymbal-like instruments shimmer much more. Secondly the bass now seemed to be less perhaps due to the greater high frequency information.
On orchestra music the orchestra is now well behind the speakers instead of right at the speaker. Like the article said, this may be a phase or time shift error and the depth may become wearing over time.
Finally there is slighlty better separation between instruments. It's easier to pick out each instrument.
- ...
- 28 posts total
- 28 posts total