Directionality for Alphacore Goertz MI 2 cable?


I am in the process of auditioning a pair of Alphacore Goertz MI(2) Veracity speaker cable. From what I have read these do not require much burn-in time, but the highs are sounding awfully bright and grainy. I've got Paradigm Studio Reference 20 v.2 monitors which have a metal tweeter (bright). But I can't believe the Alphacore cable could be quite this bad. There are no directional markings on the cables, no arrows that is. One end of each cable is labeled with the Alphacore name--is this to be considered the amp end or the speaker end? There was no instruction sheet and the packaging does not mention directionality. Can anyone advise?
salby6
Salby, I am using those cables between classe and Thiel 3.6's - I am getting no brightness at all, in fact until recently I was using all silver interconnects and still no brightness. My experience with these cables is the most neutral sound I've had in my system, with a very slight bloom and smooth highs. No burn-in required and no directionality. Could they be exposing something upstream?
The response by Lou is correct. Try the Zobel network
which Alpha-core will provide free upon request. Some
amplifiers with high negative feedback become unstable
with Goertz cables, and the Zobel will fix the problem.

I'm using MI-2 cables with a Mark Levinson 27.5 with
very pleasing results.
Goertz supplies Zobels with EVERY set of speaker cables that they sell or supply to dealers. If you did not get the Zobel network, contact your dealer and raise hell. Unless you know for sure that your amplifier will not react to a high capacitance load, you should ALWAYS use the factory supplied Zobel network. I would not consider the use of the Zobel to be "optional" in 99% of the installations out there. The factory supplied Zobels are designed to stabilize the load that the amp sees starting at appr 160 KHz, so it will not affect the sonics of the system, only the stability of the amp.

As to hearing bright and grainy, that sounds like your amplifier crying out for help. Without the Zobel network and depending on the design of your individual amplifier, you may have what is effectively a dead short to the amplifier at VERY high frequencies. This can result in smearing and distortion of the signal in-band. Take the Goertz out of your system RIGHT NOW before you run into major problems OR install the Zobel networks pronto. If you do not do this, you are looking at blowing the outputs of your amplifier and potentially your speakers.

As to the sonic characteristics that you hear after the Zobel's have been put into the system, you are hearing what your system really sounds like. Goertz cables do not suffer from skin effect, limited bandwidth, high series resistance, etc... As such, it will lay the soul of your system out before you without mercy. At the same time, it will not introduce sonics of its' own because of the aforementioned electrical characteristics. If your system still sounds bright and grainy, time to start looking for other sources of the offensive noise that you can hear.

Out of curiosity, what length of MI-2 are you currently using ?

For the record, it is not a matter of an amp using large quantities of negative feedback that can cause instability to occur with highly capacitive cables. It has to do with how the feedback network is designed and the bandwidth of the amp.

I am using those cables with a Bryston 9B driving 20 v.2 and 60 v.2 and not having any special problems with highlighting/brightness. What amp do you have?
Hi Jvogt,

Actually, it is low negative feedback, broadband amps, like Stasis and Spectral that have issues with Goertz cables. I have heard that Spectrals are so susceptible to this that they will not guarantee their gear unless you use their MIT cables, which are zobeled. Global feedback makes an amp more stable, but that comes at a price, as they do not sound as good. Nelson Pass has something on this at his site, I think it is under the article on cascode amps. The more feedback, the more you kill the highs, which kills air, etc...