2. digital
  3. 1002447905

Help with Meridian 518

Please share how you use the 518 to optimize your stereo system.

I recently added 518 to my system in place of my preamp. The 518 lets me connect my dac to my amp directly. This resulted in a much smoother and transparent sound. However, there are other functions on the 518 that are not used optimally.

I fudged around with the Emph/Deemph, different noise shaping algorithms, and the input/outbut bits, but they all sound the same to me on my system. I know for a fact they do alter the sound, for an old client had one, and he transported steisand into his living room with a mere touch of a button.

My setup:
Cal Audio Delta-Meridian 518-Cal Audio Sigma-Aragon 8002-Kef 103/4
Argent speaker cable, Emerald between amp and dac, and mapleshade between trans/518/dac

Thanks ahead of time.
viggen
sc53
689 posts
 
Another thought: when you use the 518 as a preamp, you have to set the unit up that way. There is a code you punch in right after turning it on, either 0 or 1 or 2, I can't remember which code is for the preamp and which for the resolution enhancer function. Anyway, could it be that you don't have the unit in preamp mode yet? Then I guess your choices of shapes etc. wouldn't be affecting your sound. I sold mine with the manual, of course, so I can't remember off the top of my head what the proper code is. However, I can give you the phone no. of my dealer, Mike of JS Audio in Bethesda, MD, who is an expert on all things and units Meridian and WILL be able to tell you off the top of his head.
Sarah
glaucon
25 posts
 
One more thing...

Make sure you're operating the 518 as close to unity gain as possible, i.e., 87. When I first used my unit, I could only go up to 72. The sound was great, but I didn't realize how compromised it was until I had resistors installed into the inputs of my amp, and was able to get up to the 80s. Heaven!

Remember, you lose 1-bit of resolution for every 6 db decrease.
viggen OP
817 posts
 
Hey Richard,
Believe it or not, I don't hear anything different when switching between preemph and no preemph. And, yes, my dac, the sigma, is deemphed...

Hey Sarah,
You bet I read my manual inside and out after my beloved 518 is not harnessing its full potential. And I got the type setting to 0, which is for preamp. I do believe the dsp functions, dither, wordlength and emph, are used in every mode. Only certain functions are customed differently between the various types like type 0 negates bypass to keep your speakers from going full steam ahead.

Hey Glaucon,
Did you have the same problem I've had before you installed the resistors on you amp? And what are these resistors? They sound "heavenly", where can I get my hands on them? They do not hinder with the sound quality at all? So far, I've only have my 518 up to 60, goodness how much resolution am I losing......

I made a "virtual system" and i found there is two models of 518 available amongst the choices. One with dsp and one is without. Could the problem be that I purchased a model without dsp eventhough the buttons and displays for them are still there?

Ed
vantageaudio
182 posts
 

Hello Ed! As far as I am aware there are no differences in 518 models regarding DSP function, they should all be the same

Check your software version by pressing and holding DSP whilst switching ON the 518 from the power switch on the rear. The display should read "518" and the version number (either "1.14" or "1.22"). You can also read the version when the 518 is in standby, just press the DISPLAY button

Also double-check you have selected TYPE 0 by pressing and holding SOURCE whilst switching ON the 518 from the power switch on the rear. With TYPE 0 selected, wait at least one second then switch OFF at the rear for one-half second then switch back ON again. The 518 will now be in normal mode

You could try the following settings as a start: From standby, press SOURCE - select. Then press DITHER - select FLAT. Then press DSP - select Emphasis

As Glaucon states above, try and get as close to 87 as you can. Also ensure you have selected the IN and OUT to match your transport and DAC. Pressing DISPLAY will scroll thru your selections so you can check the In and OUT settings along with the DSP and DITHER settings

Once you start listening you can then work your way thru the DITHER settings. Take your time here. Happy listening! Regards, Richard

viggen OP
817 posts
 
Hey Richard,

Thanks for being very informative!!

I checked the version of software on the 518, and I've got the older version, 1.14. I doubt the older version would penalize the audio performance?

I've already have designated the 518 as a Type 0.

It seems I am at a disadvantage for using the 518 as a preamp. Lowering the volume on the 518 cuts into the resolution of my digital source. However, using the 518 as a preamp with curtailed resolution and forgoing the DSP still sounds better than having my Nakamichi Ca-7a in the audio loop.

Ed
More to discover