Crackling sound when using a DAC


I just hooked up a Museatex DAC to a NAD CDP as transport. The NAD has a digital interconnect from it to the Museatex digital IN. From the Museatex I'm using Harmonic Technology's Interconnects to a Simaudio intergrated. The after market power cord from the DAC is plugged into an Acoustic Research surge protector.

Whenever I turn on the CDP it crackles from my speakers. The same is done when I replace a CD from the NAD drawer and the player loads, could anybody explain this? Am I doing something wrong?
lush
I always get a quick, loud and sharp crackle...its bad and very loud. I've tried everything, I have noticed that it only happens after closing the CD drawer and the cd begins to load, the speakers burst out in crackle. I have avoided this problem by switching the Museatex to optic settings, then switching back to Wire (coxial) when the disc has loaded and playing, everything seems fine.

Surely there has to be a better way so I can get rid of this very unpleasent distortion and not have to worry about switchin my DAC settings everytime I change a disc.
pbawcutt,

Do you mean that the crackle doesn't happen when the DAC's optical digital input is used ("I have avoided this problem by switching the Museatex to optic settings, then switching back to Wire")? This sounds odd, because the phenomenon that I described is totally independent of what digital input is used. Like I said, a small crackle sound is normal, but in my experience it isn't as bad as what you're describing. Perhaps your amp's input sensitivity and/or your speakers' sensitivity is higher than mine, which is exacerbating the issue. However, I doubt this is the case given that there are many Museatex DACs in the field, and I've never heard of a "normal" unit behaving like this. I'd suggest three things:

1. Try using the DAC with a friend's CD player/transport, and see if the same problem occurs. This would at least rule out that it's related to the NAD's coax output.

2. It may turn out that your unit has a problem, like a bad servo circuit that's failing to null the DC properly. It's therefore a good idea to send John Wright an email. You'll find his contact info at www.museatex.com, and I've found him to be great to work with.

3. A properly functioning unit is going to exhibit the occasional mild crackle when the CLock engages. It's simply the nature of the beast. In the end, if it turns out there's nothing "broken" with the DAC but you just can't live with this issue, and turning down the volume when you change the disc is not a satisfactory solution, then perhaps this relationship wasn't meant to be.

Best of luck.
Hey Oxia, I have my amp's volume set to 0 and it still happens. What i meant by switchin to Optic was, I only change the setting, there isn't really a wire hooked up there, but when I change to optic setting, allow the disc to load, then press play on the NAD, I switch back the DAC to wire setting, and no cracks or distortion.

It's very strange indeed.
Hmmm. So to summarize, these are the two scenarios:

A)
-The DAC is configured to use the coaxial digital input
-You then put in a CD
-The CD player reads the TOC and outputs a signal
-The DAC recognizes the signal; CLock engages
-You get a sharp "crackle" from your speaker

B)
-The DAC is configured to use the optical digital input
-You then put in a CD
-The CD player reads the TOC and outputs a signal (the DAC doesn't receive the signal because it's not hooked up via the Toslink connection)
-You switch the DAC to the coaxial input
-The DAC recognizes the signal; CLock engages
-You get no "crackle"

It sounds strange because I would think that since the ouput relay and servo are engaged when the DAC receives the signal, then if they are the cause of the problem (i.e. they are faulty) it shouldn't make a difference whether you use method "A" or "B". One possibility is that there is a brief initial "burst" discharge from the NAD's digital output when it sends a signal, which goes away after it has a second or two to settle. Perhaps this is upsetting the DAC's receiver, and by switching the DAC's input off and then on a bit later, you are effectively giving the transport's digital output enough time to settle before engaging the DAC. Have you tried using the DAC with another transport? Have you used different DACs with the NAD? Again, I would encourage you to email John Wright for his thoughts.

It was the NAD, I've since used another Transport and I didn't get the problem.

I have no idea why this happens with the NAD. I can avoid the problem by switching it to optical and then back to coax once it's loaded.

Im not sure I could buy a DAC that would beat the NAD handsdown for under $500 as a simple transport, so I might keep the NAD for awhile, I've seen a Theta and CAL audio Lab transports for sub $500 but I have no way of telling if they would be a sonic improvement to the NAD, so I might just live with it for awhile.