Atma-sphere M60 II.3-Any good for 4 ohm speaker?


Guys, I like the idea of trying OTL, but, in looking at the mfg. web page, I see the power rating going down to 40 watts for 4 ohm load, and going up to 80 watts for 16 ohm load. I am receiving my speakers next week, and they are 95DB with a 3.8-4 ohm load(Reimer Tetons)What do you think of these amps with a 4 ohm speaker. Also, why does the power go down, not up?

Thanks in advance
711smilin
Can anyone tell me the difference between the new Rendition Audio Monitor 60 and, the Atmasphere M60?

The Monitor 60 is one beautiful piece. I am assuming both these amps were designed by Ralph.

711, an auto-transformer will solve the 4-ohm issue. I used an Atmasphere MA-1 on my Magnepan 3.6's with the auto-transformer with excellent results.

But that Monitor 60.......it sure is nice looking....
As you suggest, the Rendition Audio Monitor 60 is designed by Ralph Karsten; it's styling goes back to the earlier Atma-Sphere M-60 styling that Ralph always liked. The circuit is very close to the current M-60 MkII.3 but in a different chassis.
.
711Smilin, what you see in the power output specifications of the M-60 into different impedance loads (power goes down as impedance goes down and up as impedance goes up) is characteristic of OTLs. (As contrasted to solid state where the reverse happens.) It's one of the reason OTLs traditionally do a good job with electrostatic speakers which can have dramatically rising impedances in the top end.

I don't doubt Trelja's description of his experience with 4-ohm Frieds. But the "conventional wisdom" is not just "urban myth", there's a lot of solid reality to it. Trying to drive 4-ohm speakers with M-60s will be an iffy proposition, and not just due to the reduced power. There will be increased challenges around controlling the woofers effectively due to the impedance mis-match of the M-60 to the 4-ohm speaker load. With certain specific drivers, the matching may work; apparently it does so with Trelja's Freids, but I'd be very hesitant drawing broad conclusions from a single specific example (which I think is an exception). You may get a similar result with your Reimer Tetons, but you may not.

The greater number of output tubes in the MA-1 make it a much more suitable match to a benign 4-ohm impedance curve than the M-60. The increased number of tubes in the MA-1 lowers the output impedance of the amplifier by half (compared to the M-60) and makes for better power transfer into the lower impedance load and better control over the drivers. It's not just a function of the MA-1 having higher rated power output: it's also a function of better controlling the low impedance speaker's driver.

The Zero autoformer can help. But it's not a panacea, and while there are reports from many folks who have been very pleased with the results obtained with the Zeros in their systems, there are also reports from people who not positive about the reulting sound quality.

The best way to get advice about the compatibility of the M-60s with your Reimer Tetons is to call the factory and ask Bill or Ralph: 651-690-2246 If they've had any experience with your speakers, they'll give you a straight answer about compatibility.
.
Ralph is back!

Many of you may not be aware of the fact that Ralph Karsten has returned to Atma-sphere, along with his proven track record of product development, customer service, quality, and integrity. The other parties who were briefly running Atma-sphere during Ralph's "departure" in 2004 are no longer affiliated, in any manner, with Atma-sphere. I don't wish to comment further concerning details, since I don't want to see this thread closed. In short, Atma-sphere is back to the same high quality operation for which it has been known for the past 25(?) years!

711smilin, call Atma-sphere (Ralph or Bill) since they will be able to best help you with your decision. And forget about the tax write-off, which only comes into play for an amount OVER the fair market value of a charity item!

Trelja, I would check with Atma-sphere regarding the 12SX7 tube mods. I was lead to believe that this mod was not good for transformer longevity, but I may be mistaken. I was discussing several issues about my amps, and could have misinterpreted or confused information about the 12SX7 mod.
Fatparrot,

Thanks for clarifying that "Ralph is back!" It is good to have him available at A-S once again to talk with.

As to the 12SX7 mod, I haven't heard about this creating any problems. The main considerations for Ralph when I asked about this mod are: (1) increasing cost of the 12SX7 on the vintage tube market; (2) significantly decreasing availability and no "new" production; (3) much better availability of the 6SN7, including great sounding vintage stock (although the vintage is also getting more costly). In short, he's not a fan of this mod and doesn't recommend it for these reasons even though many people report liking the sonic change.
.