MC Step Up Math


Hi all,

after posting a thread on here years ago and becoming exceedingly confused about cartridge step up maths, I gave up, embarrassing for a math major..perhaps I should have studied electrical engineering. Recently I have been reading up on this topic and would like to once and for all figure out how to run the math/electronic theory to find the correct step up to mate with a MC cartridge.

I have looked at 2 different links.

Link (1)

http://www.theanalogdept.com/sut.htm

and

Link (2)
http://www.rothwellaudioproducts.co.uk/html/mc_step-up_transformers_explai.html

Now, everything I read in link 2 falls apart after reading what is on link 1 and I am once again confused about what to look for in a MC step up.

In the second link the author explains that you simply apply a 2 step process: A. multiply the turns ratio by the cartridge output to find the voltage and make sure that it is not overloading the MM phono stage input (i.e/ between 2.5 and 10 MV) and then B. Perform the calculation to show you how much resistance the cartridge actually sees and apply a rule of thumb at least 3 to 10 times ratio between the source impedance and the input. The rule is for the most part out of thin air, though he does explain that matching to equate the 2 is a bad idea.

In the first link however, the author takes a different approach. He explains that a turns ratio cannot just be multiplied to give you the voltage on the other end. For example the cinemag 3440 cart used with the dynavector illustrates the point. The output is .30 MV and the turns ratio is 35.4 resulting in 10.6 MV out.

Now here is the bit I need help with. He explains that in reality the with this combination the output is really 5.1387mV NOT 10.6MV. He uses this equation to adjust the 10.6 MV to 5.1387MV:

(Vout / Vcart) = (R(Load_effective) / (R(Load_effective) + (Rcart)))

he finds Vout and then Multiplies by the turns ratio.

The parameters are as follows:

Rcart: is internal resistance of the MC cartridge
R(Load_effective): resistive load seen at the MC cartridge
Vout: Voltage output at secondary side of tranny
Vcart: Voltage output at MC cartridge

Hi all,

after posting a thread on here years ago and becoming exceedingly confused about cartridge step up maths, I gave up, embarrassing for a math major..perhaps I should have studied electrical engineering. Recently I have been reading up on this topic and would like to once and for all figure out how to run the math/electronic theory to find the correct step up to mate with a MC cartridge.

I have looked at 2 different links.

Link (1)

http://www.theanalogdept.com/sut.htm

and

Link (2)
http://www.rothwellaudioproducts.co.uk/html/mc_step-up_transformers_explai.html

Now, everything I read in link 2 falls apart after reading what is on link 1 and I am once again confused about what to look for in a MC step up.

In the second link the author explains that you simply apply a 2 step process: A. multiply the turns ratio by the cartridge output to find the voltage and make sure that it is not overloading the MM phono stage input (i.e/ between 2.5 and 10 MV) and then B. Perform the calculation to show you how much resistance the cartridge actually sees and apply a rule of thumb at least 3 to 10 times ratio between the source impedance and the input. The rule is for the most part out of thin air, though he does explain that matching to equate the 2 is a bad idea.

In the first link however, the author takes a different approach. He explains that a turns ratio cannot just be multiplied to give you the voltage on the other end. For example the cinemag 3440 cart used with the dynavector illustrates the point. The output is .30 MV and the turns ratio is 35.4 resulting in 10.6 MV out.

Now here is the bit I need help with. He explains that in reality the with this combination the output is really 5.1387mV NOT 10.6MV. He uses this equation to adjust the 10.6 MV to 5.1387MV:

Equation (*)
(Vout / Vcart) = (R(Load_effective) / (R(Load_effective) + (Rcart)))

he finds Vout and then Multiplies by the turns ratio.

The parameters are as follows:
Turns ratio: The turns ratio of the step up device
Rcart: is internal resistance of the MC cartridge
R(Load_effective): resistive load seen at the MC cartridge defined as 47,000/(Turns Ratio)^2
Vout: Voltage output at secondary side of tranny
Vcart: Voltage output at MC cartridge

for this example they using a denon 103 + cinemag 3440 are:
Turns Ratio: 35.4
Rcart: 40
R(Load_effective): 47,000/(35.4^2) = 37.5 ohms
Vout: to be solved for
Vcart: .30 MV

Putting it into equation (*) and solving yields
.1452mV for Vout.

He then takes Vout and multiplies by the turns ratio.

.1452 * 35.4 = 5.1387mV

NOW: If you take the simple method (from link 2 by multiplying turns with output) you get 10.6 MV, using this adjusted method with equation (*) you get 5.1387 MV. So my question is this. What is equation (*), is there some theory here that I am missing, is this voodoo? I would like a reliable way to select components that match, though I have trouble trusting the equation (*) method without knowing where why he is using it and what it is. I certainly want to get this ironed out before I start buying different transformers to play with, and any help with this would be greatly appreciated. Thanks.
dfel
Good call lewm, sure simplicity is good and when possible that is the best path. How about if it was made in 1930-1950 by a company that is long gone, or does not have the specs available any more? By applying the simple calculation, you know what you are dealing with even if that information is not available...figuring out the which tap does what (ground, phase, impedance etc..) can still be a pain.

Al you are right, it makes little difference for the 50K vs 47K it is not substantial, however there are still a lot of them quoted at 15K so I wanted to make sure I am doing the right thing, as it does make a difference in that scenario. Thanks for verifying that that method for adjustment is correct and what needs to be used in equation (*)..I was assuming it was as you said but wanted to make sure. You have been very helpful! Appreciate it, really, thanks for taking the time.

Heads up to those looking on the website for the first link as there are some calculation errors on that site with turns ratio and impedance on the cinemag example, and he also ignored the 50K bit (not as critical, to be fair)

At some point, when I am done reading on this, I will post a summary/dummy guide to these calculations that lead you to the ballpark, so anyone interested does not have to read the whole thread.
Dfel- It's not only the math and ee theory, it's also three other things:
1. No matter how well you understand the theory and do the math, the results are unpredictable.
2. Which means that unless you get really lucky, an internal step-up may not be optimal sonically, even if it is a good match electrically; which then leads to use of an outboard SUT, which requires additional interconnects. Which leads to issue #3:
3. It's my understanding that the step-up property of the transformer not only multiplies the voltage but also "multiplies" (in quotes because I don't think it's an exact relationship) the effect that the cabling has on the sound.

I'm pretty sure 1 and 2 are true, not sure about 3, but since my pre has in active gain stage that works just fine w a LO MC, I'm good to go, w/o math headaches, or trying to remember whether a higher impedance number means you are loading it down more or less, and whether you are matching the output impedance on the output device to the input impedance on the input device or vice versa.