Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
I have a cd player with 2 volts of output, but the only spec I can find on Impedance reads " load impedance over 10 kilohms". Not sure if this is suggesting the output impedance is 10,000 ohms! Does not seem possible!?

The unit is a Sony dvp ns900v sacd player. I purchased the LS for a second system and to just play with.
Do you have the TRL modded Sony 900? If so you might want to check with Paul to see about the impedance. I had one for a bit that was modded by TRL.

This is a solid state player so output impedance should not be that high. However, since it is also SACD/DVD and has a lot of other functions not relevant to 2 channel audio the impedance could be higher. I recall the manual being pretty daunting so it might be hard to pin this down.

Why don't you give it a whirl and see. I don't place as much value on the impedance matching criteria that is talked about around here as much as I used to. I've used the LSA with some pretty interesting combinations and it's worked fine each time. However, the one thing I haven't tried yet is a high output impedance source. That will happen after CES/THE SHOW with a tube phonostage I'm auditioning.
I just looked at the manual and it appears the audio output and 5.1 channel output are both listed at over 10k ohms. Not sure what more I can say at this point. The high output impedance is unusual for a solid state player but my guess is that is due to it being a DVD player as well as CD/SACD.
Thanks. Yes 10k is very high. As you saw the manual uses the term " load impedance". Oh well, seems my cd player is a potentially poor match.

I will try it. Yes, mine is the TRL mod with battery power supply and all. Paul did remove all video outputs as an FYI.