Amp vs preamp question

IMO - Amp/Speakers matching first.
Finding preamp that will complement the amp/speakers synergistic qualities is the trick. Transparency is the goal and prefered coloration - just like salt & pepper- to ones own taste. Gamma of features, ease of use, cosmetics, value - all, just iceing on the cake.
At the end, your system is or will be as good as your weakest link. Speaker>amp>pre>source>rest is my own general rule.

Unsound, good point. If he's driving the Thiels to high levels in an 18x18 room, he's got more problems than amp power; he'll be working on hearing loss. 4 Ohm nominal impedance, 90dB sensitivity. He'll be fine. I have used integrateds (i.e. Pathos Classic One MkIII, Eastern Electric M520, Dussun V8i) at moderate listening levels with less efficient speakers and they all have worked perfectly.

Now, if he wants to blow the walls out... that's a different story. Most audiophiles I know do play their gear louder than I do, so take that into consideration.

True, he can get more power with separates, but likely more cost and potentially more mismatches in gear. It's a trade off. He may want to stick with a one brand solution then.

1) A solid state amp that doubles output as speaker impedance is halved is a necessity for the Thiel speakers. MAYBE a Wolcott tube amp would work...maybe.

2) Impedance matching between preamp and amp is critical. The BAT preamp has a fairly high output impedance that limits the number of solid state amps that will match properly. Obviously, a BAT solid state amp would work well.

3) The same requirements as stated in point number 1 above apply to any integrated amp being considered. You can cross tube integrated amps off your list.

The direct answer to your question is that the amp is most important in the respect that it must match properly with your speakers. No preamp will fix a poor amp/speaker match. Next, once you have a good amp/speaker match, the preamp must match the amp in respect to impedance. A marginal impedance match between the preamp and amp will result in rolled off bass and possibly rolled off highs...despite an excellent amp/speaker match.

Bottom line...I'd recommend a good solid state integrated amplifier that doubles output as speaker impedance is halved: Pass Labs, Gryphon, Bryston...maybe even a Portal Audio Panache.

Perhaps the term “high” needs some definition… My vk5i total output imp was 800 ohms, 400 per phase… the vk32 has an output imp total of 600 and the Rex is 200 per phase or 400. .. I’m figuring the VK 51 is in there somewhere between 400 & 800 ohms total..

Unless I read an article reviewing the CJ 350 Premiere solid state amp in error, one of the two mainstays, either Mr. Conrad, or Mr. Johnson said a ratio of 10:1 is sufficient for preamp to amp matching. So if the preamp in question has an output imp of say 1000 ohms total, then the amps input imp needs to be 10,000 ohms or better…. Many amps, even the modest input impedances of Spectral amps, would meet that criteria.

My single ended thor output impedance is I think 400. it’s driven every amp I’ve connected to it with eease. 60wpc tube amps, 250wpc SS amps, 100 wpc SS etc… in to speakers with low impedances of 1.8 ohms, 4, 6, and 8ohms. With eff ratings from as low as 85 db!

So what’s a high impedance output for an active preamp??? 1100 ohms? 1500?

All the BAT amps I just looked at have input impedances of 90K +. Tube or SS.

I doubt seriously you’ll run into trouble in that preamp > amp, regard.

BTW none of the BAT amps double down in their power outputs… they just have enormous power reserves. Other’s use negative feedback to ehlp out there.

…and let’s face it… exactly when will one need to have an amp which produces 500 wpc… or 600, or 1000 wpc?

90% of the music is made in the first 20wpc anyways.

It will all come down to what your aim is for driving your loudspeakers. Wanna peel paint? Produce live rock and roll shows?

I’ve got a pair of 87db, 4 ohm speakers which drop to 2 ohms… I can run them easily with a pair of 120 wpc tube amps… very well….. or with a 150 wpc SS stereo amp too! Even with my SS HT receiver which questionably put out 110wpc!

Kevin Hayes of VAC told me once he runs many of his amps on a pair of Thiel 2.6s…. even his 30wpc SET amp! Check the specs on some of the VAC amps which are very well regarded, and you will notice they don’t double power with halved impedances.

This deal ain’t that hard. A quality amp will do well…. And here’s a thought…. Call thiel and ask them what amps on your short list they would recommend.

Usually, its the bass at lower to moderate volumes that suffers driving speakers with difficult loads with amps that are not up to the task.

IF you're willing to live with that for some other aspect of a particular amps sound, then I guess you will be fine, but you may not be getting everything that your speakers are capable of delivering at lower to moderate volume.

In my case, I replaced a 360w/ch Carver amp that did not come close to doubling output with impedance with a ~100w.ch Musical Fidelity that does.

The Carver went louder and sounded fine at higher volumes, but the bass and dynamics were noticeably missing at lower volumes. The Musical Fidelity does not go as loud, and the sound is dynamic and balanced now at the volumes I more typically listen at.