Anyone HEARD the qol 'signal completion' device?

I have a Lyngdorf room correction device. It certainly helped my room situation for sure. However, the amount of components and power cords, ect... is really busy in and around my rack. I have my TV hooked into my 2 channel system as well. So I don't want to add a component to an already busy system, but if it is true this device kind of takes the room out of the equation, then I can keep things even without having to add more. Can anyone else verify what Marc77 says about the QOL with the room? I'm sure the results are room or system dependent. I know the best way to find out, is to just try one my self. Wonder if I can get my wife to go along with yet another audio purchase? :)

I posted in another thread about my experience, but in case you haven't seen it, here it is:

So I was lucky enough to play around with a QOL in my system and here are my subjective impressions:

The build quality looks very good - along the lines of, say, Pass. It's designed to be flexible - e.g. if you have an integrated amp, you could put this between all your sources and the pre, but I believe the best way to use it is inbetween the pre and the amps, which is what I did.

As mentioned in reviews, there is a bypass button which you can toggle via remote but with the QOL enaged the perceived volume is louder so it's hard to A/B without the usual volume bias.

Listening impressions: I'm going to approach this from the standpoint of what my (amateur audio engineer) brain tells me is being changed by the QOL. First of all, the bass is pretty much unchanged. If I remember correctly, it only affects 125hz upwards. Everything above that frequency is louder - which changes the overall tonal balance to some degree. I found this mostly for the better in my system - at least at low to moderate volumes. I have plenty of bass, so more mids and highs (at least the degree to which it's augmented) seems good. It feels like it makes copies of all the information and mixes it back in with the original signal resulting in a presence/volume boost. Almost akin to 'double tracking' vocals and instruments (common recording practice to make a more palpable image) however in this case its doing it to the entire mix, not just an instrument. That means the ambience (or plain old reverb) is getting a boost as well.

The main effect to my ears is a more 'wetter' presentation. It adds 'space', as if the image was being projected in multiple directions instead of one. I suspect this is what people refer to as 'more like live music'. It IS engaging - no doubt about it, but it does come at a price: not all recordings suit this effect. For example, one of my test tracks is a Carpenters tune (yes, I do admit to listening to the Carpenters) where Karen's voice has plenty of reverb. With the QOL her voice is swimming in it and suffers from some intelligibility loss. It may still appeal to some folks - not like it sounds bad in any way, but imo it changes the character of the mix. Some track that had reverb did sound good - a Patricia Barber tune that has finger snapping sounded excellent and Patricia's voice, which already has gobs of reverb still sounded good. It varies. Classical music sounded good, as did jazz and rock (although I would still say this depends on the material). What I did find that some busy songs with instrument solos resulted in the solos being more buried in the mix (as if the engineer added reverb to it) where I prefer the more dry presentation.

Keep in ming that my Wilson speakers are very 'dry' sounding, especially in the upper frequencies. The QOL was never edgey and sounded quite smooth, despite the highs being more pronounced. I don't think I'd like this device in a very 'live' room.

The bypass switch is mandatory imo - and I think also in the manufacturer's. They warn that when playing vinyl, if an LP is noisy one may want to disengage QOL because it will emphasize the surface noise. While I haven't tried vinyl yet, I believe this to be true because with QOL engaged I can hear tube rush from my preamp at my listening position (where normally I cannot). It's truly being 'loudened' (and of course the frequencies for tube rush is midrange).

Ultimately I found that more and more I preferred my system with the unit in bypass mode as the effect was too distracting for me.

I have also posted my review of the BSG Qol after 7 days of continuous use in the Audiogon section under Preamps.

BSG Qol Review February 2012.

I received my Qol unit late in the day last Saturday via Fed Ex. The Qol unit was very cold when I unpackaged it so I let it rest. Still, I was curious as heck so I did manage to play it for about 30 minutes that night.
I installed the Qol between My Pass XP-10 Preamp and Pass Labs X350.5 Amp. I was fortunate because I had another set of balanced interconnects just like my others and a Synergistic Tesla Power cord just like my others and I even had a 1A spare HIFI Tuning fuse available.

First impression, I thought it sounded kind of bright and with limited, if any, sound quality improvement.
The next day on Sunday, I played the Qol for a while, but again, I thought it was kind of bright sounding. I attributed it to needing some break in time. I then hooked the Qol up to a tuner and continuously played music 24/7 even when I was not actually listening to my music.

Well, I am a little embarrassed to post this but what the heck.
My earlier thoughts about the Qol sounding a little bright and the sound quality lacking turned out to be because I am using way too many speaker tweaks.
I found that the spades of my AudioPrism ground controls were touching the copper body of my Walker HDL Links, (On both L and R sides). In essence it was shorting out. It must have occurred when I was rerouting some of the cabling. Once I separated them the brightness went away, the sound quality greatly improved and the soundstage expanded every which way. I could actually hear that change occur when I was behind my speakers.
I wonder if I should just remove all of my speaker tweaks? Maybe later.

Since then, I have continued to break in the Qol by continually playing music through it. I believe the sound quality is still improving. So, anyone who says it is plug and play is not getting the full potential of the unit. Not sure how long the break in should take but 200 hours seems to work best for most electronic components.

Well my room also has problems that were preventing me from fully enjoying the Qol.
The Qol is certainly a different animal than what I have been used to. The Qol needs open area to do its magic.

So first off, I have had in my room for about a decade Argent Room Lenses.
For those unfamiliar to this room correction item, they are made with 3 pipes attached to a stand called dark matter. Anyway, the pipes are designed to work as a Helmholtz Resonator. There are 3 of these units in the room. Two were flanking the outer side of the speakers and one in the center of the room. These units worked fantastic, especially before my basement dedicated room was finished and I installed defined walls.
The Room Lens captured the side reflections and defined the soundstage.

Anyway, the Qol unit works almost the opposite by expanding the soundstage. So, I removed the Argent Room Lens from the room and played some music, and yes, the soundstage opened up.

The other problem I had was my Eggleston Andra 2 speakers were extremely toed in. The Toe in angle was so much that the image was directed to the center of my head. The music sounded like Olivia Newton John had her tongue in my ear. Not necessary a bad thing, but not correct for the recorded soundstage.
Well these speakers weigh 215 lbs and have 2” Audio Point spikes on them making it very difficult to just change the toe in angle.

I found that Herbie Labs sells a glider designed for Speaker spikes and with this glider I could move the speakers. So I ordered a set of them.

I received the Speaker spike Gliders a few days later and I went about reducing the amount of toe in. After the change, the soundstage became enormous.
I now have my speakers just about at a 90 degree angle and 36” from the side walls. But I will continue to experiment with placement further.

Well now it is almost 7 days later, how does the Qol sound? One of the big benefits of the Qol is the change in dynamics. I mean it is actually hard to find a volume set point to just leave alone. The music can go from soft to loud in a heartbeat. Funny, that even though the music appears to be quite louder, my Pass Labs Amp meter moves very little. This indicates to me that the increased dynamics is not pulling anymore current from my Amp.

With the Qol engaged, the music takes on a natural sound and image. The soundstage becomes very wide and deep. My speakers virtually disappear. I know that is said all the time, and before the Qol I thought my set up was awesome, but with the Qol you can hear deep into the recordings. The center image is the best I have ever heard. I can now hear background singers clearer and my toe tapping has increased.
The frequency extremes are heard with an authority. What I mean by that is that they are no longer buried in the mix but sound like they were part of the intended sound, if that makes sense.
Not all recordings were as hyped up as others. I guess each recording has its own reverb, echo, and different out of phase anomalies.

So the $4000 question, is it worth the money ?...
Well, if you want the deepest, widest soundstage and the wildest dynamics your components can handle, what price is that worth to you?
For me, it’s a keeper, no question.

thanks for the informative review. You mentioned that it seems to be better on some recordings over others. Do really good recordings sound even better or does it help out the not so good recordings sound better? Or is it just random?

Ozzy, Thanks for that very interesting review. Now that you have changed room treatments and the positions of your speakers, how do you know that the result is from the Qol? What do you hear when you toggle the Qol in and out of the system? When it is out of the signal, is the sound better than it was before you made all of the changes? Or is all of this improvement only when you have the Qol in the loop? Do you also notice a volume change when you toggle it on and off?