Need help finding cause of hum

Try moving the amp to a different location. It could be induced by magnetic field nearby.

Sounds like you've investigated pretty thoroughly and logically. But I'm not sure what is meant by this statement:

When I reversed speaker placement (Right to Left & Left to Right) - cables staying in place - the hum stayed on the right coming out of what had been the left channel speaker.

Does that mean that each cable remained connected to the speaker it was originally connected to, and you moved the left speaker and its cable to the right side of the room, and moved the right speaker and its cable to the left side of the room? Or does it mean that the cables remained on their original sides, but the speakers themselves were moved (with the cables being disconnected and then reconnected to the other speaker which was moved to that side)?

Also, I think that Sid's suggestion sounds well worth trying. And re your last question, I wouldn't worry about damage resulting from this hum. Whatever is causing it is producing the equivalent of a very low level signal, which would seem unlikely to be harmful in any way that I can envision.

Regards,
-- Al

I would say if you haven't tried, see how the cables are oriented between the amp and the speaker. Any power supplys or AC cords near the right and not the left? Also have you checked the pre to amp cable routing? Another switch I would try is Pre to Amp reversale Lt for Rt and see if the hum switchs to the Lt channel. Also I will add that about 2 weeks ago I thought I have apower supply hum in my amp and determined that it was a wall wart powersupply for my Littlite TT lamp. You might check any of those plugged in to the same circuit. They are usually a pretty lower quaility power supply and can induce noise.

You've done a lot of good investigation without success. I think this dictates that you go back to the simplist way to solve the 'mystery hum' problem.

Disconnect everything. Unplug every thing. Then connect your speakers to you amp and plug the amp into the wall outlet. Any hum? No - then add one item, starting with the power conditioner. Listen. No hum - connect the pre-amp to the amp. No hum - plug the pre-amp in. No hum - turn it on. Etc thru all your stuff. When the hum reappears you've ID'd your problem.

PS Don't forget to turn the amp off between each change. It is easy to forget to do.

Thanks to everyone for your comments.

Yes, Sid. I was wondering about some weird magnetic field -- but affecting only the right channel? I think I'd have noticed this before as nothing in the house has changed and I've been in close proximity to both speakers as I've moved them around over the last few years. None the less, I will try later to see if moving the amp eliminates it.

Almarg - the latter...that is, I physically moved the left and right speakers but the cables that had fed them were not moved. I was initially worried I'd damaged a driver on the right speaker. Somewhat relieved that did not appear to be the case as the hum now also came from the speaker that had been on the left. Note too - before moving the speakers themselves, I had also switched connections at the back of the amp...connected the left cable/speaker to the right channel out on the amp and the right cable/speaker to the left channel out. When I did this, the hum moved to the left.

Theo - I did wonder about some possible interaction between the amp's MAC Sound Pipe power cord and right speaker cable. The power outlet for the amp is right behind the right speaker (but there is also an outlet behind the left speaker). I moved the power cord to the outlet on the left side of the equipment. The hum stayed with the right speaker and the left speaker remained quiet. It's an integrated amp so if I'm understanding your sugggestion correctly, I don't think I can change the pre-amp/amp wiring. I will take a look at the phono-preamp connection if that is what you intended, however. The power transformer for the phono-pre is on the right side of the equipment near that right speaker...maybe it has been inadvertently moved and gotten a little too close to the speaker. I will check it out.

Newbee - Good suggestion. I will try this. I did shut down and unplug the power conditioner (though I did not disconnect the inputs to the amp from phono-pre, TT & CDP when this was done) - the hum was still there.

Thanks to all once again for taking the time to reply.